Subscribe to the gold package and get unlimited access to Shamra Academy
Register a new userStudy the effect of pure silica alloy on the curve of the physical dispersion coefficient in optical fiber
دراسة أثر إشابة السيليكا النقية على منحني معامل التبدد المادي في ليف بصري
845
0 8
0.0
(
0
)
Added by
Tishreen University ورقة بحثية
Publication date
2018
fields
Physics
and research's language is
العربية
Authors
نظير ديوب( باحث )
Created by
Shamra Editor
Ask ChatGPT about the research
يهدف البحث إلى دراسة إمكانيات الحصول على مواد ذات تبدد مادي مزاح نحو الأطوال الموجية الأعلى و التي تقع ضمن النافذة C-Band المستخدمة حالياً في أنظمة الاتصالات بالألياف البصرية. يتم ذلك عن طريق إشابة مادة السيليكا النقية SiO2 بمواد مختلفة و بنسب مختلفة، حيث نقوم بإيجاد قرائن انكسار مادة اللب في ليف بصري و دراسة تغير هذه القرائن بتابعية الطول الموجي للضوء انطلاقاً من ثوابت سيلمر التي تم الحصول عليها من برنامج OptiFiber. بعد ذلك قمنا بحساب معامل التبدد المادي DM لكل من المواد المدروسة، بكتابة برنامج ماتلاب خاص بهذه الدراسة و بالتالي دراسة تغير التبدد المادي لهذه المواد بتابعية طول الموجة.
The aim of this study is to study the possibilities of obtaining materials with a material shift to the higher wavelengths that fall within the C-Band window currently used in fiber optic communication systems. This is done by mixing pure SiO2 with different materials and different percentages. We find the evidence of refraction of the core material in an optical fiber and study the change of these clues by sequential wavelength of light from the solimer constants obtained from the OptiFiber program. We then calculated the physical dispersion factor DM for each of the studied materials by writing a special matlab program for this study and thus studying the change in the physical dispersion of these materials by the sequential wave length.
References used
Malitson, I.Interspecimen Comparison of the Refractive Index of Fused Silica,OSA.55 (10),1965, 1205-1209
Saurabh; and Kumar,V. Power Communication using Optical-Fiber. IPASJ International Journal of Electrical Engineering (IIJEE). 3 (12),2015, 11-15
Dubey, P. K; and Shukla,V.Dispersion in Optical Fiber Communication. International Journal of Science & Research (IJSR). 3 (10),2014, 236-239
rate research
Read More
This research aims to study and design a single mode optical fiber using simulation,
with a core and glass cladding, and also helps in ensuring the efficiency to use the optical
fiber designed within the broading window C-Band,and that these resear
ches and studies
tries to use this window. This research also shares to set the light on the Numerical
Programmes and Simulation used now in studying and designing these optical fibers. At
first we used the programOptifiberto reach the confidence of Sellmeier equation for the
fiber core, and this completed by using the finite element method solving the equation of
propagation the electric field and finding its 3-D distribution, using the famous simulating
COMSOLMultiphysics. This completed by putting the program MATLAB to reach the
two equation: the total dispersion and attenuation for the designed optical fiber.
Optical fiber is one of the most important communications media in communication
system. Due to its versatile advantages and negligible transmission loss it is used in high
speed data transmission. There are various types of optical fiber, the Fibe
r Bragg Grating
(FBG) is commonly chosen as important components to compensate the dispersion in
optical communication system. Because the low cost of filter for wavelength selection and
low insertion loss, it has also customized reflection spectrum and wide bandwidth. The
simulation of transmission system will be analyzed based on different parameters using
OptiSystem simulator. By simulating a model of communication system and using the
most suitable settings of the system which include input power, fiber cable length (km) and
attenuation coefficient (dB/km) at cable section, there are three different parameters will be
investigated, which are Signal power, Noise power, output power at receiver.
This research aims to study the impact of physical evidence in
achieving customer satisfaction and so on Kiwan Palace restaurant
in Damascus. The researcher has distributed 130 questionnaires
to a group of attendees of this restaurant was which (116)
refundable and valid for the analysis of a questionnaire which
accounted for 89.23% of the total covered by the research which
is a good ratio.
The chromatic dispersion of fiber is a major factor
causing distortion of the light signals, and if not being
addressed using accurate compensators it will lead to a
significant deterioration in the performance of optical system.
The value of chr
omatic dispersion is not fixed along the fiber,
and this necessitates the use of tunable dispersion
compensators which need information about the value of
dispersion which is done by dispersion monitoring.
This research is Interested in analyzing chromatic
dispersion technique based on the measuring of clock tone
power of transmitted data and which is commensurate with
the dispersion of the fiber. We found the relationship between
signal frequency with range and accuracy of measurement.
Also, the advantage of this technique to provide feedback
signal to tunable dispersion compensator. The results show
the extent of the improvement made in network performance.
VPItransmissionmaker program was used to simulate
the technique proposed.
ABSTRACT
This paper presents the measurement of the laser Threshold damage of an optical surface at different roughness coefficients. The study procedure is achieved
through the manufacturing of two types of parallel-sided borosilicate plate (Glass
Bk7, and SF13).
The Laser used is ND: YAG pulsed laser and the longitudinal mode TEM00 laser pulses with pulse width τ =30ns and wave length λ=1.064μm, the laser
beam is focused using F=30 mm lens. The concentrated laser beam is guided by a converging lens towards the optical surface of the parallel surface plate.
Finally, we obtained a graph of roughness coefficient is drawn in relation the optical Threshold Damage of the optical surface, Before and after processing
the optical surface. We were able to raise the threshold by about 15% after conducting thermal treatment of the optical surface.
suggested questions
Log in to be able to interact and post comments
comments
Fetching comments
Sign in to be able to follow your search criteria
