The aim of the study was to study the ability of the leaves of the figs (Ficus
retusa L.) and (Phoenix dactylifera L.) in the city of Tartous to accumulate the
lead elements (Pb), nickel (Ni).
This study aimed to estimate the level of air pollution in some portable heavy metals
in dust quarries by needles of Pinus brutia Ten. as biomonitor In site of Kfardabeel Stand-
Jableh. The samples of dust and leaves were collected at the end of Ju
ly in 2016, Atomic
absorption spectrophotometer was used to determine the amounts of Lead, Zinc, Nickel
(ppm, dry weight).
The average of accumulated metals in the needles were estimated: (Pb= 45.57 ppm,
Zn= 13.64 ppm, Ni= 7.64 ppm), while their amounts in the dust were done as following:
(Pb= 66.1 ppm, Zn= 15.8 ppm, Ni= 19.6 ppm). The results showed that the studied site is
polluted with Pb and Ni whereas Zn is in the natural range. a strong correlation between
heavy metals amounts in the needles and their amounts in the trapped dust (r= 0.98) was
detected, also regression equations have explained the variations in accumulation of
studied metals in relation to the accumulated dust on needles as following: 40% Pb, 40%
Zn, 20% Ni. Consequently results confirmed the possibility of detecting the atmospheric
Pb, Zn, Ni pollution in the studied site using P. brutia Needles as a biomonitor.
This research focuses on determination the concentration of some heavy metal
elements (Nickel Ni and Cadmium Cd) in the coastal water sediments of Ras Al-Basit
(Latakia ) during the period that range between Autumn 2013 and Summer 2014 using the
A
tomic Absorption (Atomic Absorption Spectrophotometer: AAS) at two different (closed
and open) geographical regions.
The results of the research indicate a correlation monumental between the change in
the concentration of studied metallic elements (Ni & Cd), the quality and sediment
sampling sites on the one hand, and the sources of pollution on the other. It observed the
rule of fine sand with minor amount of clay in the sediments collected from closed area;
with high concentrations of both Nickel (755.50mg/Kg), and Cadmium (71.30μg/ Kg),
compared with the open area while the majority of the sediments are medium sand with
low Nickel and Cadmium concentrations (38.85mg/Kg; 13.31μg/ Kg).
Direct high sensitive spectrophotometric method for determination
Ni(III) has been suggested . proposed method is based on the
formation of red- win colored complex between Ni(III) and DMG
reagent in strong alkaline media of NaOH ,pH=12.5.the formed
complex absorbed electromagnetic radiation at 465nm .
This study has been conducted to identify the levels of heavy
metals (lead, cadmium, nickel, cobalt, copper, iron, manganese, and
zinc) in the following spices: Nutmeg, turmeric, cinnamon, ginger,
cardamom, nigella sativa, black pepper, cumin, coriander, curry,
and mixed spices.
The concentrations of copper (Cu), zinc (Zn), nickel (Ni), lead (Pb),
cadmium (Cd) in dead and live honeybees were determined by using
atomic absorption spectrophotometry. The samples were collected from
beehives of stationary apiariessituated in
five different locations of
Latakia; Qardahah (Asitamo), Haffeh (Dabba), Jableh (Snouper),Latakia
city (Al-Ramel Al-Shamali\ Autostrade of Al-Jomhouria) and Eastern
Entryway to Latakia (behind Al-Jood factory) , during the spring and
autumn in 2014.
The objective of this study was to determine the effect
pepsi cola on the change in concentration of nickel ion in the saliva of
patients with fixed orthodontic appliances.
This study was conducted to identify the levels of heavy metals (lead, cadmium, mercury, nickel, copper, iron, zinc) in the following processed local and imported meat: Sardine (canned full), Tuna (canned chunks), Hammour (frozen full), Euphrates Fis
h (frozen full), fish produced at Qattinah Lake in Syria (frozen full) , lamb (frozen ground), beef (frozen ground), lamb sausage (frozen full), beef sausage (frozen full), sausageproduced in Netherlands (frozen stuffed), lamb liver (frozen full), broiler chicken liver (frozen full), broiler chicken (frozen full), chicken mortadella (canned), beef mortadella (canned), chicken mortadella (canned) produced in Netherlands. Heavy metal concentrations were identified in the samples of the studied meat by atomic absorption spectrometer. The concentrations taken in the wet weight measured in (ppm) were as follows: lead values range between (0.1–5.61),cadmium(0.01–2.02), mercury (0.14 –79.01), nickel (0.11 - 0.82), copper (0.24 – 6.89), iron (1.01 - 91.03), zinc (8.14 - 45.5). It was noticed that in some of the studied samples of the imported and locally-processed meat the levels of lead, cadmium, mercury, and nickel were above the levels permitted by WHO (World Health Organization) and by FAO (Food and Agriculture Organization).While the concentrations of copper, iron, and zincwere belowthelevels permitted.
Welded joints corrosion phenomena for some kinds of stainless steels and nickel alloy was studied in
polluted phosphoric acid 37.7%H3Po4 using electrochemical techniques like Tafel polarization. Corrosion
rate of base metal and weld metal had calcu
lated & compared among these alloys.
Laboratory Test results showed the change in both corrosion rate and corrosion current densities (Icorr)
for tested alloys, and there is a clear difference between base metal and weld metal in most of tested alloys
, which lead to high corrosion rates of welded joint, and change in its properties then gets out of service in
some service conditions. The stainless steel 904L has low corrosion rates and low difference in corrosion
rates between base metal and weld metal, so it may be the most suitable alloy, among all the studied
alloys, for exploitation in polluted phosphoric acid 37.7%H3Po4 produced at the General Fertilizer
Company in Homs city.
Partial veneer crown has appeared to prevent the excessive preparation of
dental tissue with complete crown and the major reason success of this prosthesis could be strength of
cementation.
Therefore the latest studies have been focusing on develo
ping new material and technique to increase the
bonding strength and using new technique for surface treatment or change type of metal alloy.
The aim of this search is to study the bonding resin cement strength to different type of metal alloy due to
surface treatment.
