Subscribe to the gold package and get unlimited access to Shamra Academy
Register a new userReduction of Vertical Raw Mill Vibration Effect on control Instruments beam in New Hama Cement Factory By Tuned Mass ى Damper ى(TMD)
تخفيض تأثير الاهتزازات الناتجة عن المطحنة العمودية للمواد على الجائز الحامل لأجهزة التحكم في معمل إسمنت حماة الجديد باستخدام مخمد الكتلة الديناميكي ( TMD )
546
0 13
0
(
0
)
Authors
هادي المحمد( باحث )
Created by
Shamra Editor
Ask ChatGPT about the research
يهدف هذا البحث إلى دراسة تخفيض تأثير الإهتزازات الناتجة أثناء عمل المطحنة العمودية التي تقوم بطحن المواد الأولية اللازمة لإنتاج مادة الإسمنت في معمل إسمنت حماة الجديد على أجهزة التحكم المركزي الواقعة في مبنى يبعد حوالي 100 متر عن هذه المطحنة , حيث أن زيادة شدة الإهتزاز تؤدي إلى اهتزاز الجوائز الحاملة لأجهزة التحكم و تسبب ضرر في العناصر الإلكترونية.
This research drives at studying the reduction of vibration effect on central control system located on about 100 m of the Vertical mill running at New Hama Cement factory , which grinds raw materials necessary for cement production ,Whereas , the increase of vibration intensity leads to vibrate control Instruments beams and the electronic elements will be damaged.
References used
FLSmidth Engineering company A/S., ( 2011). - ATOX raw mill . Copenhagen, Denmark
IBM International Business Machines Corporation., ( 2012). - PureFlex System-Planning for the system, Armonk, New York
Metwally H.M., Slman F.K., EL Lakany A.M., (1993). - An Improved Matrix Method for the Dynamic Response for Modeling Structure under Moving Vehicles . Proceeding in the International Modal Analysis Conference IMAC, Held in kissimmee, Florida, USA
rate research
Read More
The study aims to identify the effect of Physical and moral
incentives which provided to employees in the Cement's factory in
Tartous on their satisfaction on their work, and to shed some light
on the incentive systems applied to employees in that sector.
This research was performed to study the effect of sewage water on
the surface water of the Addelbeh Valley stream, and groundwater
on both sides of the stream in Tartous Cement Factory area.
Water samples were taken from the factory water outlet
and
Addelbeh Valley water to study the content of pollutants. We also
took groundwater samples from selected wells on both sides of the
waterway in the studied area. We repeated that process every two
months for a full hydrological cycle from July 2013 to May 2014.
We found a great increase in content of the industrial drainage
water include oils and heavy metals especially iron, copper and
zinc. For example: iron concentration in sewage water exceeded
150 mg/l in all samples. Besides sewage water and stream water
contained high concentrations of ammonia and nitrite versus low
concentration of nitrate, unlike water wells samples. The study
revealed increased EC and salts concentration markedly in wells
water due to its adjacency to the sea.
This research deals with study and analysis the issue of adjust and control the production process by using the Quality Control Charts (Control Panels) for variables , in order to measure products quality during production process , by knowing deviat
ions amount occurring in production process , causes, time and place deviation then take appropriate corrective actions.
the quality control charts show graphic measurements over time and show the lower, central, and upper limits of the process that we want to control and quality control in order to distinguish between natural changes that caused by general reasons inherent in the process and the changes that caused by specific reasons.
The research focuses on kinds of Quality Control Charts, the case have been applied on Jood Factory for assembly electrical tools, such as Control Charts for variables which includes Average chart ( X ̅- chart ) , standard deviation chart (s ̅ – chart), range chart
(R – chart), and units chart (X– chart), the control lines were drawn by using SPSS program.
The research concludes realistic results confirm that the company doesn't have an application of statistical techniques in quality control such as Quality Control Charts and there isn't clear scientific method according to athletic basis followed in process control.
Jood company has certificates of Syrian and European standards of quality control so it had to be a recommendation for the company related to use statistical control charts in all production stages , and put periodic developmental specialist training programs in quality control field with the need to include a statistical cadre to staff working in the company, and the importance of measuring process capability to make sure of its abilityto achieve quality within the specified standards, and use control limits of six standard deviation about process average.
Therefore in this paper we will present the stability analysis carried out on the
Dwesat dam with vertical core, its high is 33m, the downstream slope of 1V:2.75H and the
upstream slope of 1V:3.0H. Thickness of the vertical core was varied from 1V:
0.25H to
1V:2.0H, and also present the effect of the varied thickness on slope stability for both
upstream and downstream under three design conditions i.e. during and end of
construction, steady state seepage and rapid draw down by General Limit Equilibrium
Method using GeoStudio software.
It was observed from the analysis that by varying the thickness of vertical core of
earth dam, thinner core up to 1V:1.30H gives more stability and further increase in
thickness of core tends to sharp decline in factor of safety for both upstream and
downstream slope under different design conditions.
This research aims to:
Determination of optimal pH values to reach the highest
efficiency of chromium removal in industrial wastewater from
tanneries by chemical deposition.
Access to close concentration of the permitted
concentration of chromium in treated tannery wastewater
according to Syrian Standard No. 2580/2002 (Table 1).
Log in to be able to interact and post comments
comments
Fetching comments
Sign in to be able to follow your search criteria
