Subscribe to the gold package and get unlimited access to Shamra Academy
Register a new userImprove the rheological properties of asphalt (60-70) by adding polypropylene
تحسين الخواص الريولوجية للبيتومين (60-70) بإضافة البولي بروبلين
1336
2 20
0.0
(
0
)
Added by
Tishreen University ورقة بحثية
Publication date
2018
fields
Transportation
and research's language is
العربية
Authors
بسام سلطان( باحث )
Created by
Shamra Editor
Ask ChatGPT about the research
يلعب البيتومين دور المغلف و الرابط للحصويات في المجبول البيتوميني، و يتعرض لمجموعة من التغيرات التي تبدأ من مرحلة إنتاج المجبول البيتوميني إلى مرحلة استثماره تحت تأثير الحمولات المرورية و العوامل الجوية. يهدف هذا البحث إلى التحقق من إمكانية استخدام بوليمير البولي بروبلين لتعديل خواص الرابط البيتوميني و لزيادة مقاومته لدرجات الحرارة المرتفعة و زيادة ممانعته للظروف المناخية المختلفة ، من خلال تعديل عينات البيتومين بإضافة البولي بروبلين بنسب (1 ، 2 ، 3 ، 4 ،6 ، 8 %) ، و من ثم إجراء الاختبارات على عينات البيتومين المعدل و تتضمن الغرز ، الاستطالة ، نقطة التمييع ، و حساب دليل الغرز . و باستخدام فرن الطبقة الرقيقة الدوار RTFOT قمنا بإجراء التقادم قصير الأمد على عينات البيتومين العادي و المعدل و حساب الفاقد بالحرارة و الغرز المتبقي و دليل التقادم ، كما قمنا بإجراء اختبار التركيب المجموعي لتحديد مركبات البيتومين . بينت نتائج الدراسة أن قيم الغرز تميل للانخفاض مع زيادة نسبة الاضافة بينما ترتفع درجة التمييع ، كما بينت النتائج زيادة ممانعة البيتومين المعدل للظروف الحرارية ، و أن النسبة المثالية لإضافة البولي بروبلين تتراوح بين (7 %) حيث يكون عندها دليل التقادم في الحالة الموجبة و الفاقد بالحرارة في أدنى مستوى .
Asphalt plays the role of envelope and bonding in asphalt gable, and is exposed to a range of changes that start from the stage of production of asphalt mosses to the stage of investment under the influence of traffic loads and weather factors. The aim of this research is to investigate the possibility of using polypropylene polymer to modify the properties of the asphalt binder and to increase its resistance to high temperatures and different climatic conditions by modifying the asphalt by adding polypropylene by (1, 2, 3, 4, 6, 8%) And perform traditional tests on modified asphalt samples . Using Thin film oven test RTFOT test to perform the short-term Aging on normal and modified asphalt samples, heat loss, residual Penetration and aging index, And conduct a structural composition test to determine asphalt compounds. The results of the study showed that the values of Penetration tend to decrease with the increase of the percentage of addition while the degree of Softening point. The results showed increased resistance of asphalt modified to the thermal conditions. The optimum percentage of polypropylene is 3% Loss on heat at the lowest level.
References used
Henglong Zhang, Zihao Chen, Guoqing Xu, Caijun Shi. Evaluation of aging behaviors of asphalt binders through different rheological indices . Fuel 221 (2018) 78–88
Samy Dekhli, Khedidja Ait Mokhtar, Ferhat Hammoum and Djaffar Si Bachir . Rheological Behaviour of Ethylene-Vinyl-Acetate (EVA) Modified Road Bitumen . Journal of Applied Sciences Volume 15 (3): 444-455, 2015
Maria A. Vargas , Miguel A. Vargas , Antonio Sanchez-Solis , Octavio Manero . Asphalt/polyethylene blends: Rheological properties, microstructure and viscosity modeling . Construction and Building Materials 45 (2013) 243–250
rate research
Read More
The objective of this research is to study the effect of wood ash in
rheological properties of Self – compacting mortar (SCM). By
implemented some mixtures with different percentage from wood
ash with two kinds of cement and three kinds of super plasticizer
and study the effect in slump flow and yield stress to this
mixtures.
This paper is targeting towards studying on the possibility to modify some properties
of unsaturated Polyester compounds by adding rubber materials in order to improve its
flexibility property. For this target, Waste of cars' tires was used in two
forms powder and
pieces, and the liquid rubber Styrene-butadiene was used as another type of rubber. After
that the modification was detected by measuring the possibility of the resulted compound
materials to absorb vibration power, and reduce the noise that is produced by eccentric
crankshaft circulation at different rotating speeds, (300, 500, 700) rpm.
Test results demonstrate that there will be Modification in the construction of the
compounds at low rotating speeds (300 rpm). On the other hand, it demonstrates different
results at high rotating speeds.
The purpose of this research is to study the improvement of soil properties by the
addition of lime in certain percentages. The soil used in this study was obtained from the
Baseet region, which is located by the Syrian coast. We have studied the e
ffect of lime on
the consistency, the swell characteristics and the shear strength of soil.
The results of this study have shown a remarkable reduction of both liquid and
shrinkage limits, and the plasticity index with the increase of lime percentage. As for
plasticity limit, it increases in the beginning then decreases slightly with the rising of lime
percentage.
For the volumetric variation, the susceptibility of swelling and the shrinkage of
improved soil with lime decrease, and the free swelling and the swelling pressure become
almost negligible with 4% of lime.
Based on the shear strength results, we can indicate a notable increase in the friction
angle and cohesion of soil with increasing of lime percentage up to 8% of lime. After that,
these two factors decrease.
Some kinetic parameters have been determined in this work for thermal and catalytic
cracking of the mixed of polyethylene and polypropylene using batch method. The
cracking reaction was carried out at different temperature 470,490 and 510oC under
atmospheric pressure. The mass of products (liquid and gas fractions) were determined and
used to plot the curves of the thermal and catalytic decomposition. We used two types of
catalysts: Syrian natural Zeolite and the same after loading with sulfate ions using
impregnation method. The thermal cracking has a long time and has firs-pseud order
reaction. While in the case of catalytic process we note that the reaction finished in the
short time and the process is the Zero-pseud order reaction. The rate of the cracking
increased very much, the rate constant was k1=0.0032.min-1 in the thermal cracking at
4700C and ko=0.111.min-1 in the case of catalytic cracking in presence of Z catalyst and
ko= 0.206 min-1 in presence of 15-SO4
2-/Z as catalytic at the same temperature. In the other
hand activation energy was 208.7 kj/mol in the thermal process and decreased to 116.6
kj/mol at Z catalytic presence and to 87.3 kj/mol at 15-SO4
2-/Z catalytic presence.
This research with additives of kaolin is
being carried out in order to improve different types of clay soil. It was
studied the nature and extent of the change on final product.
suggested questions
Log in to be able to interact and post comments
comments
Fetching comments
Sign in to be able to follow your search criteria
