Subscribe to the gold package and get unlimited access to Shamra Academy
Register a new userDefining the plasma parameters of solid red Copper depending on (LIPS) technique and by using Nd:YAG laser
تعيين وسائط بلازما النحاس الصلب الأحمر اعتمادا على تقنية (LIPS) باستخدام ليزر Nd:YAG
1340
3 12
0
(
0
)
Added by
Aِl-Baath University ورقة بحثية
Publication date
2018
fields
Physics
and research's language is
العربية
Created by
Shamra Editor
Ask ChatGPT about the research
يدرس هذا البحث مطيافية البلازما المتولدة بالليزر (LIPS) باستخدام ليزر Nd:YAG النبضي عالي الطاقة. تم تركيز شعاع الليزر على أهداف صلبة و هي عينات من النحاس الأحمر (النقي بنسبة % 99.5.), تم قياس أهم الوسائط البلازمية و هي درجة الحرارة و الكثافة الإلكترونية.
This paper discuss the Laser induced breakdown spectroscopy (LIBS) by using Nd:YAG which is a high energy pulsed Laser . The laser radiation is focused on solid targets which are samples of red Copper (99.5%). Most important Plasma parameters which are electron temperature and density was measured.
References used
RAY V, 2013- Laser Induced Breakdown Spectroscopy, Indor, Vol. 4. 1-8
KCOMPITSAS. M ROUBANI F, BASSIOTIS I, 2000- LIPS As an effect method for elemental analysis of Environmental Samples, EASEL.1-9
BITTENCOURT A, 2004- Fundamentals of Plasma Physics, New York, USA, 515
rate research
Read More
The study was conducted on randomized samples of virgin olive oils
collected from Hama, Aleppo, Daraa, Latakia, Homs and Idleb to investigate
the relationship between the quality indices of oil purity (peroxide value, the
figure iodine, coefficien
t of acidity, the absorption coefficient qualitative Xultraviolet
K270 and distributed fatty acids) and related volatile flavor
components compared with what is published in the literature. The results also
showed that the quality indices of Hama and Lattakia، s samples in terms of
extra virgin olive oil and the first class of virgin olive oil were not compatible
with the Syrian Standards and metrology (2000/182) while the concentrations
of fatty acids for samples of Idleb, Homs, Latakia, Deraa and Aleppo were
within the scope of Syrian standard. However, their distribution in Hama
samples did not comply with the ratios set forth in the Syrian specifications.
Forty three volatile compounds were isolated and they correspond with what is
published. The samples of research showed somewhat of similarity to a large
extent with the exception of a sample of Hama, where a decline was observed in
the content of volatile flavored materials. It was noticed that the essential
composition of volatile compounds of the samples was aldehydes followed by
ester of fatty acids and then hydrocarbons. The study showed that the
technique used in this research was fast and efficient in extraction and
identification of volatile compounds.
In this research the development of the conditions of the determine copper duo by spectrophotometric method that based on the formation of a complex with Alizarin Red S was accamplished with the presence of fallow acid when the wavelength(220 nm), th
at by studying the effect of PH and the impact if the interference caused by the presence of some metal ions (nickel ions, chromiun ions, 2 inc ions, calciom ions, and triple iron ions) which make it difficult for the progress of determine copper by Alizarin Red S. the best PH value for this process is (pH = 9.5) and the relationship of Lambert Bear realized within the range 0.2 – 125 mg/ml the detection limit was 0.OO1µg/ml.
Due to the importance of Strontium Titanate in modern
technological industries, optical devices, solar cells and other
utilization; in this research we study the synthesis of ST from
SrCO3:TiO2 (1:1).
This work was focused on the synthesis of tetradentate Schiff bases which
were prepared by condensation of salicylaldehyde with 1,4-diaminobenzene
and 1,3-diaminobenzene. The Schiff base ligands were checked by different
spectral technique (GC-MS,
1H-NMR, IR). The influences of shaking time on
the extraction of Cu (II) using solvent extraction technique was studied. Then
the Kinitic parameters were calculated from schemes which give best line
through drawing log (a-x) vs time or 1/(a-x) vs time or [Cu2+] vs time, whereas
(a-x) represents Cu(II) concentration in water phase and from it (n) reaction
order, (K) reaction rate constant (t1/2) reaction half between prepared ligand
and Cu (II) were calculated.
The copper wire drawing is one of cold forming operations which
basicly the copper is used as pure material for various diameters &
sections in electrical conductors industry.
By cooperation with S.M.C company for cables industry in
Damascus – Sy
ria, a research has been done during 2 years on rod
breakdown heavy drawing machine -HENRICH - GERMANY- 2
lines- with max productivity 25 ton/24hr.
50 samples of copper wire breaks and deformations have been
studied & analyzed, thus the defects are classified in main statistics
diagrams in gold of give main instructions that contribute in raising
the quality level of local copper wire manufacturing & giving a
whole view about this industry.
suggested questions
Log in to be able to interact and post comments
comments
Fetching comments
Sign in to be able to follow your search criteria
