Subscribe to the gold package and get unlimited access to Shamra Academy
Register a new userDesign and development of a device (sensors system) to Study the effect of operational defects, which include 15% or less of the cross-section of the concrete bore pile on the resistance to lateral and axial loads
تصميم و تطوير جهاز (منظومة حساسات) لدراسة تأثير العيوب التنفيذية التي تشمل على % 15 أو أقل من المقطع العرضي للوتد البيتوني المحفور على مقاومته للقوى الأفقية و الشاقولية
1042
0 8
0
(
0
)
Added by
Aِl-Baath University ورقة بحثية
Publication date
2016
fields
Geotechnical Engineering
and research's language is
العربية
Created by
Shamra Editor
Ask ChatGPT about the research
في هذا البحث تم تصميم و تطوير جهاز (منظومة حساسات) لدراسة تأثير العيوب التنفيذية للوتد البيتوني المحفور بهدف إيجاد عوامل المقاومة المناسبة R للأوتاد البيتونية المحفورة بالعيوب التنفيذية التي تشمل على % 15 أو أقل من المقطع العرضي للوتد البيتوني من خلال إجراء اختبارات على نماذج مصغرة للأوتاد تحت تأثير الحمولات الأفقية و الشاقولية.
In this paper the design and development of a device (sensors system) to study the effect of operational flaws of dowel Albetona engraved: In order to find the appropriate resistance R factors for the to concrete bored pile executive defects, which include 15% or less than the cross section of the to concrete bored pile by conducting tests on miniature models of the pegs under the influence of horizontal and vertical loads.
References used
Sami W. Tabsha, Michael W. O’Neill, Moon S. Nam,( 2005). "Shear strength of drilled shafts with minor" Engineering Structures,Vol. 27, PP. 736–74
M. O’Neill, S.W. Tabsh, H. Sarhan, (2002). "Response of drilled shafts with minor flaws to axial and lateral loads",Engineering Structures Vol. 25,PP. 47-56
H. A. Sarhan, and M. W. O'Neill , (2005). "Resistance Factors for Drilled Shafts with Minor Defects",Department of Civil and Environmental Engineering University of Houston
rate research
Read More
Using high strength concrete made a big step in designing and
constructing reinforced concrete structures. In this research, shear
resistance of high strength concrete beams with average resistance
of (65Mpa) and without shear reinforcement was ca
lculated by
making Experimental tests, also we studied the effect of cross
section shape on shear resistance, and measured the deflection in the
middle of the beams then we compared these results with the
mathematical results and with results from other researchers, finally
we developed a relationship to determine shear capacity in high
strength concrete T beams.
The copper wire drawing is one of cold forming operations which
basicly the copper is used as pure material for various diameters &
sections in electrical conductors industry.
By cooperation with S.M.C company for cables industry in
Damascus – Sy
ria, a research has been done during 2 years on rod
breakdown heavy drawing machine -HENRICH - GERMANY- 2
lines- with max productivity 25 ton/24hr.
50 samples of copper wire breaks and deformations have been
studied & analyzed, thus the defects are classified in main statistics
diagrams in gold of give main instructions that contribute in raising
the quality level of local copper wire manufacturing & giving a
whole view about this industry.
The mid-transverse section is considered one of the significant sections in the
shiphull, because it exists in the middle of its calculated length, where the bindings
moments reach the maximum, in consequence the hull strength can be determined thr
ough
the strength of this section. Its design process includes the determination of the dimensions
of plats and different framing beams and considered one of the important stages in the hull
design process. This research includes the estimation of calculated values of binding
moments, inertia and resistant’s moments of this section area, initiated from the providing
conditions of critical strength and fatigue strength. It also includes, the formals used for the
determination of longitudinal elements dimensions through the transverse thicknesses and
metal distribution type among them. The longitudinal strength of the hull was evaluated
according the perpendicular and tangential stresses.
In this Thesis, we have studied, designed and implemented
an energy and economic efficient smart plug system and achieves
high rates of performance. At the beginning, a comprehensive
reference studying the Smart Plug devices. The Smart Plug device
was studied, designed and implemented using, which Turn-Off
electrical loads in Standby mode to minimize power consumption.
The status of all devices connected to the smart plug is shown on
the computer display using smart monitor application.
The design and implementation of Smart Plug system has saved
1.3% of the total energy consumed in the home per month while
achieving economic feasibility and improving the cost of the
economic return of the total consumers about 0.7% through the use
of the smart plug that has been implemented.
It is very important to the design and development of
natural isolating materials Which are used in the cover-up of solid waste landfill, clay soils or mixtures of these soils and some
additions used as an impermeable liner for construction of soli
d
waste landfill, The permeability coefficient of the materials used in the impermeable system is the most important factors to prevent water leakage into the body of landfill site and to prevent the Leachate of leak into groundwater and soil surrounding the landfillsites.
In this research has been the development and design
Oedometer cell to study volumetric distortions occurring in these
soils as a result of exposure of these soils to climatic conditions
during the implementation of impermeable layer or after
implementation due to rising temperatures in landfill because of
biological interactions taking place at these landfill.
It has been modified and the development of Oedometer
cell to become a thermal cell So that it can control the degree of
heat applied to the sample in the ring of device and then measure the volumetric changes in the sample, Oedometer cell has been linked to the permeability test system with variable head to measure the permeability of the testing sample, It was connected with the digital control , measuring and showing system for temperature and load and displacement.
Log in to be able to interact and post comments
comments
Fetching comments
Sign in to be able to follow your search criteria
