اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدNOAA Image Data Acquisition to Determine Soil Moisture in Arequipa-Peru
96
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
In recent years, irrigations have been built on dry areas in Majes-Arequipa. Over time, the irrigations water forms moist areas in lower areas, which can have positive or negative consequences. Therefore, it is important to know in advance where the water from the new irrigation will appear. The limited availability of real-time satellite image data is still a hindrance to some applications. Data from NOAAs environmental satellites are available fee and license free. In order to receive data, users must obtain necessary equipment. In this work we present a satellite data acquisition system with an RTL SDR receiver, two 137-138 Mhz designed antennas, Orbitron, SDRSharp, WXTolmag and MatLab software. We have designed two antennas, a Turnstile Crossed dipole antenna with Balun and a quadrifilar helicoidal antenna. The antennas parameter measurements show very good correspondence with those obtained by simulation. The RTL SDR RTL2832U receiver, combined with our antennas and software, forms the system for recording, decoding, editing and displaying Automatic Picture Transmission (APT) signals. The results show that the satellite image receptions are sufficiently clear and descriptive for further analysis.
قيم البحث
اقرأ أيضاً
The Mu3e experiment aims to find or exclude the lepton flavour violating decay $mu^+to e^+e^-e^+$ with a sensitivity of one in 10$^{16}$ muon decays. The first phase of the experiment is currently under construction at the Paul Scherrer Institute (PS
I, Switzerland), where beams with up to 10$^8$ muons per second are available. The detector will consist of an ultra-thin pixel tracker made from High-Voltage Monolithic Active Pixel Sensors (HV-MAPS), complemented by scintillating tiles and fibres for precise timing measurements. The experiment produces about 100 Gbit/s of zero-suppressed data which are transported to a filter farm using a network of FPGAs and fast optical links. On the filter farm, tracks and three-particle vertices are reconstructed using highly parallel algorithms running on graphics processing units, leading to a reduction of the data to 100 Mbyte/s for mass storage and offline analysis. The paper introduces the system design and hardware implementation of the Mu3e data acquisition and filter farm.
One of the optimization goals of a particle accelerator is to reach the highest possible beam peak current. For that to happen the electron bunch propagating through the accelerator should be kept relatively short along the direction of its travel. I
n order to obtain a better understanding of the beam composition it is crucial to evaluate the electric charge distribution along the micrometer-scale packets. The task of the Electro-Optic Detector (EOD) is to imprint the beam charge profile on the spectrum of light of a laser pulse. The actual measurement of charge distribution is then extracted with a spectrometer based on a diffraction grating. The article focuses on developed data acquisition and processing system called the High-speed Optical Line Detector (HOLD). It is a 1D image acquisition system which solves several challenges related to capturing, buffering, processing and transmitting large data streams with use of the FPGA device. It implements a latency-optimized custom architecture based on the AXI interfaces. The HOLD device is realized as an FPGA Mezzanine Card (FMC) carrier with single High Pin-Count connector hosting the KIT KALYPSO detector. The solution presented in the paper is probably one of the world fastest line cameras. Thanks to its custom architecture it is capable of capturing at least 10 times more frames per second than fastest comparable commercially available devices.
The XENON1T liquid xenon time projection chamber is the most sensitive detector built to date for the measurement of direct interactions of weakly interacting massive particles with normal matter. The data acquisition system (DAQ) is constructed from
commercial, open source, and custom components to digitize signals from the detector and store them for later analysis. The system achieves an extremely low signal threshold below a tenth of a photoelectron using a parallelized readout with the global trigger deferred to a later, software stage. The event identification is based on MongoDB database queries and has over 97% efficiency at recognizing interactions at the analysis energy threshold. A readout bandwidth over 300 MB/s is reached in calibration modes and is further expandable via parallelization. This DAQ system was successfully used during three years of operation of XENON1T.
We present a novel methodology of augmenting the scattering data measured by small angle neutron scattering via an emerging deep convolutional neural network (CNN) that is widely used in artificial intelligence (AI). Data collection time is reduced b
y increasing the size of binning of the detector pixels at the sacrifice of resolution. High-resolution scattering data is then reconstructed by using AI deep super-resolution learning method. This technique can not only improve the productivity of neutron scattering instruments by speeding up the experimental workflow but also enable capturing kinetic changes and transient phenomenon of materials that are currently inaccessible by existing neutron scattering techniques.
The JSNS$^{2}$ (J-PARC Sterile Neutrino Search at J-PARC Spallation Neutron Source) experiment aims to search for neutrino oscillations over a 24 m short baseline at J-PARC. The JSNS$^{2}$ inner detector is filled with 17 tons of gadolinium(Gd)-loade
d liquid scintillator (LS) with an additional 31 tons of unloaded LS in the intermediate $gamma$-catcher and an optically separated outer veto volumes. A total of 120 10-inch photomultiplier tubes observe the scintillating optical photons and each analog waveform is stored with the flash analog-to-digital converters. We present details of the data acquisition, processing, and data quality monitoring system. We also present two different trigger logics which are developed for the beam and self-trigger.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
