اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدSpontaneous deformation and fission of oil droplets on an aqueous surfactant solution
61
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
We investigated the spontaneous deformation and fission of a tetradecane droplet containing palmitic acid (PA) on a stearyltrimethylammonium chloride (STAC) aqueous solution. In this system, the generation and rupture of the gel layer composed of PA and STAC induce the droplet deformation and fission.To investigate the characteristics of the droplet-fission dynamics, we obtained the time series of the number of the droplets, and confirmed that the number has a peak at a certain STAC concentration. Since the fission of the droplet should be led by the deformation, we analyzed four parameters which may relate to the fission dynamics from the spatio-temporal correlation of the droplet-boundary velocity. As a result, we found that the faster deformation would be the key factor for the fission dynamics.
قيم البحث
اقرأ أيضاً
Hydrophobic PMMA colloidal particles, when dispersed in oil with a relatively high dielectric constant, can become highly charged. In the presence of an interface with a conducting aqueous phase, image charge effects lead to strong binding of colloid
al particles to the interface, even though the particles are wetted very little by the aqueous phase. In this paper, we study both the behavior of individual colloidal particles as they approach the interface, and the interactions between particles that are already interfacially bound. We demonstrate that using particles which are minimally wetted by the aqueous phase allows us to isolate and study those interactions which are due solely to charging of the particle surface in oil. Finally, we show that these interactions can be understood by a simple image-charge model in which the particle charge $q$ is the sole fitting parameter.
Hypothesis: By combining the experimental small- and wide-angle x-ray scattering (SWAXS) method with molecular dynamics simulations and the theoretical complemented-system approach it is possible to obtain detailed information about the intra- and in
ter-molecular structure and dynamics of the solvation and hydration of the surfactant in organic and mixed solvents, e.g., of the nonionic surfactant Brij 35 (C12E23) in alcohols and aqueous alcohol-rich ternary systems. This first application of the complemented-system approach to the surfactant system will promote the use of this powerful methodology that is based on experimental and calculated SWAXS data in studies of colloidal systems. By applying high-performance computing systems, such an approach is readily available for studies in the colloidal domain. Experiments: SWAXS experiments and MD simulations were performed for binary Brij 35/alcohol and ternary Brij 35/water/alcohol systems with ethanol, n-butanol and n-hexanol as the organic solvent component at 25 {deg}C. Findings: We confirmed the presence of solvated Brij 35 monomers in the studied organic media, revealed their preferential hydration and discussed their structural and dynamic features at the intra- and inter-molecular levels. Anisotropic effective surfactant molecular conformations were found. The influence of the hydrophobicity of the organic solvent on the hydration phenomena of surfactant molecules was explained.
We investigate the break-up of Newtonian/viscoelastic droplets in a viscoelastic/Newtonian matrix under the hydrodynamic conditions of a confined shear flow. Our numerical approach is based on a combination of Lattice-Boltzmann models (LBM) and Finit
e Difference (FD) schemes. LBM are used to model two immiscible fluids with variable viscosity ratio (i.e. the ratio of the droplet to matrix viscosity); FD schemes are used to model viscoelasticity, and the kinetics of the polymers is introduced using constitutive equations for viscoelastic fluids with finitely extensible non-linear elastic dumbbells with Peterlins closure (FENE-P). We study both strongly and weakly confined cases to highlight the role of matrix and droplet viscoelasticity in changing the droplet dynamics after the startup of a shear flow. Simulations provide easy access to quantities such as droplet deformation and orientation and will be used to quantitatively predict the critical Capillary number at which the droplet breaks, the latter being strongly correlated to the formation of multiple neckings at break-up. This study complements our previous investigation on the role of droplet viscoelasticity (A. Gupta & M. Sbragaglia, {it Phys. Rev. E} {bf 90}, 023305 (2014)), and is here further extended to the case of matrix viscoelasticity.
In this study, micro-droplets are placed on thin, glassy, free-standing films where the Laplace pressure of the droplet deforms the free-standing film, creating a bulge. The films tension is modulated by changing temperature continuously from well be
low the glass transition into the melt state of the film. The contact angle of the liquid droplet with the planar film as well as the angle of the bulge with the film are measured and found to be consistent with the contact angles predicted by a force balance at the contact line.
When two sessile drops of the same liquid touch, they merge into one drop, driven by capillarity. However, the coalescence can be delayed, or even completely stalled for a substantial period of time, when the two drops have different surface tensions
, despite being perfectly miscible. A temporary state of non-coalescence arises, during which the drops move on their substrate, only connected by a thin neck between them. Existing literature covers pure liquids and mixtures with low surface activities. In this paper, we focus on the case of large surface activities, using aqueous surfactant solutions with varying concentrations. It is shown that the coalescence behavior can be classified into three regimes that occur for different surface tensions and contact angles of the droplets at initial contact. However, not all phenomenology can be predicted from surface tension contrast or contact angles alone, but strongly depends on the surfactant concentrations as well. This reveals that the merging process is not solely governed by hydrodynamics and geometry, but also depends on the molecular physics of surface adsorption.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
