ترغب بنشر مسار تعليمي؟ اضغط هنا

Flame interactions in a stratified swirl burner: flame stabilization, combustion instabilities and beating oscillations

71   0   0.0 ( 0 )
 نشر من قبل Aimee Morgans
 تاريخ النشر 2021
  مجال البحث فيزياء
والبحث باللغة English




اسأل ChatGPT حول البحث

The present article investigates the interactions between the pilot and main flames in a novel stratified swirl burner using both experimental and numerical methods. Experiments are conducted in a test rig operating at atmospheric conditions. The system is equipped with the BASIS (Beihang Axial Swirler Independently-Stratified) burner fuelled with premixed methane-air mixtures. To illustrate the interactions between the pilot and main flames, three operating modes are studied, where the burner works with: (i) only the pilot flame, (ii) only the main flame, and (iii) the stratified flame (with both the pilot and main flames). We found that: (1) In the pilot flame mode, the flame changes from V-shape to M-shape when the main stage is switched from closed to supplying a pure air stream. Strong oscillations in the M-shape flame are found due to the dilution of the main air to the pilot methane flame. (2) In the main flame mode, the main flame is lifted off from the burner if the pilot stage is supplied with air. The temperature of the primary recirculation zone drops substantially and the unsteady heat release is intensified. (3) In the stratified flame mode, unique beating oscillations exhibiting dual closely-spaced frequencies in the pressure spectrum. is found. This is observed within over narrow window of equivalence ratio combinations between the pilot and main stages. Detailed analysis of the experimental data shows that flame dynamics and thermoacoustic couplings at these two frequencies are similar to those of the unstable pilot flame and the attached main flame cases, respectively. Large Eddy Simulations (LESs) are carried out with OpenFOAM to understand the mechanisms of the time averaged flame shapes in different operating modes. Finally, a simple acoustic analysis is proposed to understand the acoustic mode nature of the beating oscillations.



قيم البحث

اقرأ أيضاً

Neural networks (NN) are implemented as sub-grid flame models in a large-eddy simulation of a single-injector liquid-propellant rocket engine. The NN training process presents an extraordinary challenge. The multi-dimensional combustion instability p roblem involves multi-scale lengths and characteristic times in an unsteady flow problem with nonlinear acoustics, addressing both transient and dynamic-equilibrium behaviors, superimposed on a turbulent reacting flow with very narrow, moving flame regions. Accurate interpolation between the points of the training data becomes vital. The NNs proposed here are trained based on data processed from a few CFD simulations of a single-injector liquid-propellant rocket engine with different dynamical configurations to reproduce the information stored in a flamelet table. The training set is also enriched by data from the physical characteristics and considerations of the combustion model. Flame temperature is used as an extra input for other flame variables to improve the NN-based model accuracy and physical consistency. The trained NNs are first tested offline on the flamelet table. These physics-aware NN-based closure models are successfully implemented into CFD simulations and verified by being tested on various dynamical configurations. The results from those tests compare favorably with counterpart table-based CFD simulations.
We show experimentally and numerically that when a weak shock interacts with a finger flame in a narrow channel, an extremely efficient mechanism for deflagration to detonation transition occurs. This is demonstrated in a 19-mm-thick channel in hydro gen-air mixtures at pressures below 0.2 atm and weak shocks of Mach numbers 1.5 to 2. The mechanism relies primarily on the straining of the flame shape into an elongated alligator flame maintained by the anchoring mechanism of Gamezo in a bifurcated lambda shock due to boundary layers. The mechanism can increase the flame surface area by more than two orders of magnitude without any turbulence on the flame time scale. The resulting alligator-shaped flame is shown to saturate near the Chapman-Jouguet condition and further slowly accelerate until its burning velocity reaches the sound speed in the shocked unburned gas. At this state, the lead shock and further adiabatic compression of the gas in the induction zone gives rise to auto-ignition and very rapid transition to detonation through merging of numerous spontaneous flames from ignition spots. The entire acceleration can occur on a time scale comparable to the laminar flame time.
The mixing process of multiple jets of liquefied petroleum gas and air in a diffusion flame is numerically analysed. The case study considers a four-port array burner where the fuel is injected by four peripheral nozzles and mixed with the surroundin g air. Simulations are conducted with the Reynolds-Averaged Navier-Stokes technique, and the turbulence effect is modelled with the realizable k-e model. In addition, the eddy dissipation model is implemented to calculate the effect of the turbulent chemical reaction rate. Results show that the essential mixture mechanism occurs within a flame cone derived from the fuel jets interaction. However, the mixing process is driven by jets drag allowing an air/fuel smooth mixture to reach the flammability limits at two zones: one at a lower location or close to the burner surface and a second before the flame front development. The entire mixing mechanism culminates with the development of the flame necking cone. Any air concentration that falls into the cone radius will be entrained, contributing to the overall flame structure. Since the cone radius reach is limited only by radial distance of the jet array and the nozzles distance, the flame heights, consequently, depend solely on fuel mass flow.
This paper presents a flame-height correlation for laminar to transition-to-turbulent regime diffusion flames. Flame-height measurements are obtained by means of numerical and experimental studies in which three high definition cameras were employed to take frontal, lateral and 45{deg} angled images simultaneously. The images were analysed using an image-processing algorithm to determine the flame-height through indirect measurement. To locate an overall chemical-flame-length, numerical simulations were conducted with the unsteady Reynolds-Averaged Navier-Stokes technique. The eddy-dissipation model was also implemented to calculate chemical reaction rate. The experiments show that this proposed correlation has an adjustment variation of luminous flame-height for the laminar regime of 16.9%, which indicates that, without the use of the intermittent buoyant flame-height correlation, it globally best represents the flame-height in this regime. For the laminar and transition-to-turbulence regime the adjustment variations are 5.54% compared to the most accepted flame-height correlations, thus providing an acceptably good fitting. The numerical results show that the proposed range for the chemical-flame-length is located between the luminous and flickering flame zone compared to the experimental flame images. These results agree with the chemical length zone reported in the literature. Therefore, the correlation can be used for laminar and transition-to-turbulent combustion regimes.
The critical dimension necessary for a flame to propagate in suspensions of fuel particles in oxidizer is studied analytically and numerically. Two types of models are considered: First, a continuum model, wherein the individual particulate sources a re not resolved and the heat release is assumed spatially uniform, is solved via conventional finite difference techniques. Second, a discrete source model, wherein the heat diffusion from individual sources is modeled via superposition of the Greens function of each source, is employed to examine the influence of the random, discrete nature of the media. Heat transfer to cold, isothermal walls and to a layer of inert gas surrounding the reactive medium are considered as the loss mechanisms. Both cylindrical and rectangular (slab) geometries of the reactive medium are considered, and the flame speed is measured as a function of the diameter and thickness of the domains, respectively. In the continuum model with inert gas confinement, a universal scaling of critical diameter to critical thickness near 2:1 is found. In the discrete source model, as the time scale of heat release of the sources is made small compared to the interparticle diffusion time, the geometric scaling between cylinders and slabs exhibits values greater than 2:1. The ability of the flame in the discrete regime to propagate in thinner slabs than predicted by continuum scaling is attributed to the flame being able to exploit local fluctuations in concentration across the slab to sustain propagation. As the heat release time of the sources is increased, the discrete source model reverts back to results consistent with the continuum model. Implications of these results for experiments are discussed.
التعليقات
جاري جلب التعليقات جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
mircosoft-partner

هل ترغب بارسال اشعارات عن اخر التحديثات في شمرا-اكاديميا