ترغب بنشر مسار تعليمي؟ اضغط هنا

Highly flexible electromagnetic interference shielding films based on ultrathin Ni/Ag composites on paper substrates

94   0   0.0 ( 0 )
 نشر من قبل Weiwei Zhao
 تاريخ النشر 2020
  مجال البحث فيزياء
والبحث باللغة English




اسأل ChatGPT حول البحث

Highly flexible electromagnetic interference (EMI) shielding material with excellent shielding performance is of great significance to practical applications in next-generation flexible devices. However, most EMI materials suffer from insufficient flexibility and complicated preparation methods. In this study, we propose a new scheme to fabricate a magnetic Ni particle/Ag matrix composite ultrathin film on a paper surface. For a ~2 micro meter thick film on paper, the EMI shielding effectiveness (SE) was found to be 46.2 dB at 8.1 GHz after bending 200,000 times over a radius of ~2 mm. The sheet resistance (Rsq) remained lower than 2.30 Ohm after bending 200,000 times. Contrary to the change in Rsq, the EMI SE of the film generally increased as the weight ratio of Ag to Ni increased, in accordance with the principle that EMI SE is positively related with an increase in electrical conductivity. Desirable EMI shielding ability, ultrahigh flexibility, and simple processing provide this material with excellent application prospects.



قيم البحث

اقرأ أيضاً

Paper based thermoresistive sensors are fabricated by rubbing WS2 powder against a piece of standard copier paper, like the way a pencil is used to write on paper. The abrasion between the layered material and the rough paper surface erodes the mater ial, breaking the weak van der Waals interlayer bonds, yielding a film of interconnected platelets. The resistance of WS2 presents a strong temperature dependence, as expected for a semiconductor material in which charge transport is due to thermally activated carriers. This strong temperature dependence makes the paper supported WS2 devices extremely sensitive to small changes in temperature. This exquisite thermal sensitivity, and their fast response times to sudden temperature changes, is exploited thereby demonstrating the usability of a WS2-on-paper thermal sensor in a respiration monitoring device.
Fabrication techniques such as laser patterning offer excellent potential for low cost and large area device fabrication. Conductive polymers can be used to replace expensive metallic inks such as silver and gold nanoparticles for printing technology . Electrical conductivity of the polymers can be improved by blending with carbon nanotubes. In this work, formulations of acid functionalised multiwall carbon nanotubes (f-MWCNT) and poly (ethylenedioxythiophene) [PEDOT]: polystyrene sulphonate [PSS] were processed, and thin films were prepared on plastic substrates. Conductivity of PEDOT: PSS increased almost four orders of magnitude after adding f-MWCNT. Work function of PEDOT:PSS/f-MWCNT films was ~ 0.5eV higher as compared to the work function of pure PEDOT:PSS films, determined by Kelvin probe method. Field-effect transistors source-drain electrodes were prepared on PET plastic substrates where PEDOT:PSS/f-MWCNT were patterned using laser ablation at 44mJ/pulse energy to define 36 micron electrode separation. Silicon nanowires were deposited using dielectrophoresis alignment technique to bridge the PEDOT:PSS/f-MWCNT laser patterned electrodes. Finally, top-gated nanowire field effect transistors were completed by depositing parylene C as polymer gate dielectric and gold as the top-gate electrode. Transistor characteristics showed p-type conduction with excellent gate electrode coupling, with an ON/OFF ratio of ~ 200. Thereby, we demonstrate the feasibility of using high workfunction, printable PEDOT:PSS/MWCNT composite inks for patterning source/drain electrodes for nanowire transistors on flexible substrates.
We demonstrate a novel concept for operating graphene-based Hall sensors using an alternating current (AC) modulated gate voltage, which provides three important advantages compared to Hall sensors under static operation: 1) The sensor sensitivity ca n be doubled by utilizing both n- and p-type conductance. 2) A static magnetic field can be read out at frequencies in the kHz range, where the 1/f noise is lower compared to the static case. 3) The off-set voltage in the Hall signal can be reduced. This significantly increases the signal-to-noise ratio compared to Hall sensors without a gate electrode. A minimal detectable magnetic field Bmin down to 290 nT/sqrt(Hz) and sensitivity up to 0.55 V/VT was found for Hall sensors fabricated on flexible foil. This clearly outperforms state-of-the-art flexible Hall sensors and is comparable to the values obtained by the best rigid III/V semiconductor Hall sensors.
217 - Xiansong Shi , Lei Wang , Nina Yan 2021
Membranes derived from ultrathin polymeric films are promising to meet fast separations, but currently available approaches to produce polymer films with greatly reduced thicknesses on porous supports still faces challenges. Here, defect-free ultrath in polymer covering films (UPCFs) are realized by a facile general approach of rapid solvent evaporation. By fast evaporating dilute polymer solutions, we realize ultrathin coating (~30 nm) of porous substrates exclusively on the top surface, forming UPCFs with a block copolymer of polystyrene-block-poly(2-vinyl pyridine) at room temperature or a homopolymer of poly(vinyl alcohol) (PVA) at elevated temperatures. With subsequent selective swelling to the block copolymer and crosslinking to PVA, the resulting bi-layered composite structures serve as highly permeable membranes delivering ~2-10 times higher permeability in ultrafiltration and pervaporation applications than state-of-the-art separation membranes with similar rejections and selectivities. This work opens up a new, facile avenue for the controllable fabrication of ultrathin coatings on porous substrates, which shows great potentials in membrane-based separations and other areas.
100 - Andreas Hemmetter 2021
Flexible energy harvesting devices fabricated in scalable thin-film processes are important components in the field of wearable electronics and the Internet of Things. We present a flexible rectenna based on a one-dimensional junction metal-insulator -graphene diode, which offers low-noise power detection at terahertz (THz) frequencies. The rectennas are fabricated on a flexible polyimide film in a scalable process by photolithography using graphene grown by chemical vapor deposition. A one-dimensional junction area reduces the junction capacitance and enables operation in the D-band (110 - 170 GHz). The rectenna on polyimide shows a maximum voltage responsivity of 80 V/W at 167 GHz in free space measurements and minimum noise equivalent power of 80 pW/$sqrt{text{Hz}}$.
التعليقات
جاري جلب التعليقات جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
mircosoft-partner

هل ترغب بارسال اشعارات عن اخر التحديثات في شمرا-اكاديميا