ترغب بنشر مسار تعليمي؟ اضغط هنا

Laser patterned polymer/nanotube composite electrodes for nanowire transistors on flexible substrates

113   0   0.0 ( 0 )
 نشر من قبل Maxim Shkunov
 تاريخ النشر 2017
  مجال البحث فيزياء
والبحث باللغة English




اسأل ChatGPT حول البحث

Fabrication techniques such as laser patterning offer excellent potential for low cost and large area device fabrication. Conductive polymers can be used to replace expensive metallic inks such as silver and gold nanoparticles for printing technology. Electrical conductivity of the polymers can be improved by blending with carbon nanotubes. In this work, formulations of acid functionalised multiwall carbon nanotubes (f-MWCNT) and poly (ethylenedioxythiophene) [PEDOT]: polystyrene sulphonate [PSS] were processed, and thin films were prepared on plastic substrates. Conductivity of PEDOT: PSS increased almost four orders of magnitude after adding f-MWCNT. Work function of PEDOT:PSS/f-MWCNT films was ~ 0.5eV higher as compared to the work function of pure PEDOT:PSS films, determined by Kelvin probe method. Field-effect transistors source-drain electrodes were prepared on PET plastic substrates where PEDOT:PSS/f-MWCNT were patterned using laser ablation at 44mJ/pulse energy to define 36 micron electrode separation. Silicon nanowires were deposited using dielectrophoresis alignment technique to bridge the PEDOT:PSS/f-MWCNT laser patterned electrodes. Finally, top-gated nanowire field effect transistors were completed by depositing parylene C as polymer gate dielectric and gold as the top-gate electrode. Transistor characteristics showed p-type conduction with excellent gate electrode coupling, with an ON/OFF ratio of ~ 200. Thereby, we demonstrate the feasibility of using high workfunction, printable PEDOT:PSS/MWCNT composite inks for patterning source/drain electrodes for nanowire transistors on flexible substrates.



قيم البحث

اقرأ أيضاً

195 - Adam M. Weidling 2021
Fabricating high-performance and/or high-density flexible electronics on plastic substrates is often limited by the poor dimensional stability of polymer substrates. This can be mitigated by using glass carriers during fabrication, but removing the p lastic substrate from a large-area carrier without damaging the electronics remains challenging. Here we present a large-area photonic lift-off (PLO) process to rapidly separate polymer films from rigid carriers. PLO uses a 150 microsecond pulse of broadband light from flashlamps to lift off functional thin films from a glass carrier substrate coated with a light-absorber layer (LAL). A 3D finite element model indicates that the polymer/LAL interface reaches 865 degrees C during PLO, but the top surface of the PI reaches only 118 degrees C. To demonstrate the feasibility of this process in the production of flexible electronics, an array of indium zinc oxide (IZO) thin-film transistors (TFTs) was fabricated on a polyimide substrate and then photonically lifted off from the glass carrier. The TFT mobility was 3.15 cm2V-1s-1 before and after PLO, indicating no significant change during PLO. The flexible TFTs were mechanically robust, with no reduction in mobility while bent. The PLO process can offer unmatched high-throughput solutions in large-area flexible electronics production.
Highly flexible electromagnetic interference (EMI) shielding material with excellent shielding performance is of great significance to practical applications in next-generation flexible devices. However, most EMI materials suffer from insufficient fl exibility and complicated preparation methods. In this study, we propose a new scheme to fabricate a magnetic Ni particle/Ag matrix composite ultrathin film on a paper surface. For a ~2 micro meter thick film on paper, the EMI shielding effectiveness (SE) was found to be 46.2 dB at 8.1 GHz after bending 200,000 times over a radius of ~2 mm. The sheet resistance (Rsq) remained lower than 2.30 Ohm after bending 200,000 times. Contrary to the change in Rsq, the EMI SE of the film generally increased as the weight ratio of Ag to Ni increased, in accordance with the principle that EMI SE is positively related with an increase in electrical conductivity. Desirable EMI shielding ability, ultrahigh flexibility, and simple processing provide this material with excellent application prospects.
However, their electrocatalytic activity is still poorly understood. This work deciphers the origin of the catalytic activity of counter-electrodes (CEs)/current collectors made of self-standing carbon nanotubes fibers (CNTfs) using Co$^(+2)$/Co$^(+3 )$ redox couple electrolytes. This is based on comprehensive electrochemical and spectroscopic characterizations of fresh and used electrodes applied to symmetric electrochemical cells using platinum-based CEs as a reference. As the most relevant findings, two straight relationships were established: i) the limiting current and stability increase rapidly with surface concentration of oxygen-containing functional groups, and ii) the catalytic potential is inversily related to the amount of residual metallic Fe catalyst nanoparticles interspersed in the CNTf network. Finally, the fine tune of the metallic nanoparticle content and the degree of functionalization enabled fabrication of efficient and stable dye-sensitized solar cells with cobalt electrolytes and CNTf-CE outperforming those with reference Pt-CEs.
We study the percolation properties for a system of functionalized colloids on patterned substrates via Monte Carlo simulations. The colloidal particles are modeled as hard disks with three equally-distributed attractive patches on their perimeter. W e describe the patterns on the substrate as circular potential wells of radius $R_p$ arranged in a regular square or hexagonal lattice. We find a nonmonotonic behavior of the percolation threshold (packing fraction) as a function of $R_p$. For attractive wells, the percolation threshold is higher than the one for clean (non-patterned) substrates if the circular wells are non-overlapping and can only be lower if the wells overlap. For repulsive wells we find the opposite behavior. In addition, at high packing fractions the formation of both structural and bond defects suppress percolation. As a result, the percolation diagram is reentrant with the non-percolated state occurring at very low and intermediate densities.
Printed electronics rely on the deposition of conductive liquid inks, typically onto polymeric or paper substrates. Among available conductive fillers for use in electronic inks, carbon nanotubes (CNTs) have high conductivity, low density, processabi lity at low temperatures, and intrinsic mechanical flexibility. However, the electrical conductivity of printed CNT structures has been limited by CNT quality and concentration, and by the need for nonconductive modifiers to make the ink stable and extrudable. This study introduces a polymer-free, printable aqueous CNT ink, and presents the relationships between printing resolution, ink rheology, and ink-substrate interactions. A model is constructed to predict printed feature sizes on impermeable substrates based on Wenzel wetting. Printed lines have conductivity up to 10,000 S/m. The lines are flexible, with < 5% change in DC resistance after 1,000 bending cycles, and <3% change in DC resistance with a bending radius down to 1 mm. Demonstrations focus on (i) conformality, via printing CNTs onto stickers that can be applied to curved surfaces, (ii) interactivity using a CNT-based button printed onto folded paper structure, and (iii) capacitive sensing of liquid wicking into the substrate itself. Facile integration of surface mount components on printed circuits is enabled by the intrinsic adhesion of the wet ink.
التعليقات
جاري جلب التعليقات جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
mircosoft-partner

هل ترغب بارسال اشعارات عن اخر التحديثات في شمرا-اكاديميا