اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدSubstrate-Versatile Direct-Write Printing of Carbon Nanotube-Based Flexible Conductors, Circuits, and Sensors
90
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
Printed electronics rely on the deposition of conductive liquid inks, typically onto polymeric or paper substrates. Among available conductive fillers for use in electronic inks, carbon nanotubes (CNTs) have high conductivity, low density, processability at low temperatures, and intrinsic mechanical flexibility. However, the electrical conductivity of printed CNT structures has been limited by CNT quality and concentration, and by the need for nonconductive modifiers to make the ink stable and extrudable. This study introduces a polymer-free, printable aqueous CNT ink, and presents the relationships between printing resolution, ink rheology, and ink-substrate interactions. A model is constructed to predict printed feature sizes on impermeable substrates based on Wenzel wetting. Printed lines have conductivity up to 10,000 S/m. The lines are flexible, with < 5% change in DC resistance after 1,000 bending cycles, and <3% change in DC resistance with a bending radius down to 1 mm. Demonstrations focus on (i) conformality, via printing CNTs onto stickers that can be applied to curved surfaces, (ii) interactivity using a CNT-based button printed onto folded paper structure, and (iii) capacitive sensing of liquid wicking into the substrate itself. Facile integration of surface mount components on printed circuits is enabled by the intrinsic adhesion of the wet ink.
قيم البحث
اقرأ أيضاً
Kapton HN films, adopted worldwide due to their superior thermal durability (up to 400 {deg}C), allow the high temperature sintering of nanoparticle based metal inks. By carefully selecting inks and Kapton substrates, outstanding thermal stability an
d anti-delaminating features are obtained in both aqueous and organic solutions and were applied to four novel devices: a solid state ion selective nitrate sensor, an ssDNA based mercury aptasensor, a low cost protein sensor, and a long lasting organic thin film transistor (OTFT). Many experimental studies on parameter combinations were conducted during the development of the above devices. The results showed that the ion selective nitrate sensor displayed a linear sensitivity range with a limit of detection of 2 ppm. The mercury sensor exhibited a linear correlation between the RCT values and the increasing concentrations of mercury. The protein printed circuit board (PCB) sensor provided a much simpler method of protein detection. Finally, the OTFT demonstrated a stable performance with mobility values for the linear and saturation regimes, and the threshold voltage. These devices have shown their value and reveal possibilities that could be pursued.
We have characterized the conductivity of carbon nanotubes (CNT) fibers enriched in semiconducting species as a function of temperature and pulsed laser irradiation of 266 nm wavelength. While at high temperatures the response approaches an Arrhenius
law behavior, from room temperature down to 4.2 K the response can be framed, quantitatively, within the predictions of the fluctuation induced tunneling which occurs between the inner fibrils (bundles) of the samples and/or the elementary CNTs constituting the fibers. Laser irradiation induces an enhancement of the conductivity, and analysis of the resulting data confirms the (exponential) dependence of the potential barrier upon temperature as expected from the fluctuation induced tunneling model. A thermal map of the experimental configuration consisting of laser-irradiated fibers is also obtained via COMSOL simulations in order to rule out bare heating phenomena as the background of our experiments. (*) Author
This work proposes new chemical and mechanical materials and techniques for III-V semiconductor NW/silicone membrane formation and optoelectronic device fabrication. Molecular beam epitaxy (MBE)-synthesized n-, p- and i-GaP NWs were encapsulated by i
ntroduced G-coating method into synthesized polydimethylsiloxane-graft-polystyrene and released from the Si growth substrate. The fabricated membranes were contacted with different materials including single-walled carbon nanotubes or ferrocenyl-containing polymethylhydrosiloxane with and without multi-walled carbon nanotubes doping. The electrical connection of the fabricated membranes was verified by electron beam induced current (EBIC) spectroscopy. The developed methods and materials can be applied for fabrication of high quality flexible inorganic optoelectronic devices.
Fabrication techniques such as laser patterning offer excellent potential for low cost and large area device fabrication. Conductive polymers can be used to replace expensive metallic inks such as silver and gold nanoparticles for printing technology
. Electrical conductivity of the polymers can be improved by blending with carbon nanotubes. In this work, formulations of acid functionalised multiwall carbon nanotubes (f-MWCNT) and poly (ethylenedioxythiophene) [PEDOT]: polystyrene sulphonate [PSS] were processed, and thin films were prepared on plastic substrates. Conductivity of PEDOT: PSS increased almost four orders of magnitude after adding f-MWCNT. Work function of PEDOT:PSS/f-MWCNT films was ~ 0.5eV higher as compared to the work function of pure PEDOT:PSS films, determined by Kelvin probe method. Field-effect transistors source-drain electrodes were prepared on PET plastic substrates where PEDOT:PSS/f-MWCNT were patterned using laser ablation at 44mJ/pulse energy to define 36 micron electrode separation. Silicon nanowires were deposited using dielectrophoresis alignment technique to bridge the PEDOT:PSS/f-MWCNT laser patterned electrodes. Finally, top-gated nanowire field effect transistors were completed by depositing parylene C as polymer gate dielectric and gold as the top-gate electrode. Transistor characteristics showed p-type conduction with excellent gate electrode coupling, with an ON/OFF ratio of ~ 200. Thereby, we demonstrate the feasibility of using high workfunction, printable PEDOT:PSS/MWCNT composite inks for patterning source/drain electrodes for nanowire transistors on flexible substrates.
Delta ($delta$) phase comprising polyvinylidene fluoride (PVDF) nanoparticles are fabricated through electrospray technique by applying 0.1 MV/m electric field at ambient temperature and pressure, which is 10$^{3}$ times lower than the typical value,
required for $delta$-phase transformation. The X-ray diffraction (XRD) and selected area electron diffraction (SAED) patterns are clearly indicating the $delta$-phase formation. The piezo- and ferro- electric response of the $delta$-PVDF nanoparticles has been demonstrated through scanning probe microscopic technique based on piezoresponse force microscopy (PFM). The vertical piezoelectric response, indicated by d$_{33}$ coefficient, is found $sim$-11 pm/V. Kink propagation model is adopted to justify the $delta$-phase conversion in electrospray system. The electrical response from $delta$-PVDF nanoparticle comprised nanogenerator under the external impacts and acoustic signal indicates that molecular ferroelectric dipoles responsible for piezoelectric responses, are poled in-situ during nanoparticle formation, thus further electrical poling is not necessary.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
