Subscribe to the gold package and get unlimited access to Shamra Academy
Register a new userA 600 Volt Multi-Stage, High Repetition Rate GaN FET Switch
130
0
0.0
(
0
)
Added by
Saewert, Gregory W.
Publication date
2017
fields
Physics
and research's language is
English
Ask ChatGPT about the research
No Arabic abstract
Using recently available GaN FETs, a 600 Volt three-stage, multi-FET switch has been developed having 2 nanosecond rise time driving a 200 Ohm load with the potential of approaching 30 MHz average switching rates. Possible applications include driving particle beam choppers kicking bunch-by-bunch and beam deflectors where the rise time needs to be custom tailored. This paper reports on the engineering issues addressed, the design approach taken and some performance results of this switch.
rate research
Read More
A broadband travelling wave kicker operating with 80 MHz repetition rates is required for the new PIP-II accelerator at Fermilab. We present a technique to drive simultaneously four series-connected enhancement mode GaN-on-silicon power transistors by means of microwave photonics techniques. These four transistors are arranged into a high voltage and high repetition rate switch. Using multiple transistors in series is required to share switching losses. Using a photonic signal distribution system is required to achieve precise synchronization between transistors. We demonstrate 600 V arbitrary pulse generation into a 200 Ohm load with 2 ns rise/fall time. The arbitrary pulse widths can be adjusted from 4 ns to essentially DC.
High-repetition-rate sources of bright electron bunches have a wide range of applications. They can directly be employed as probes in electron-scattering setups, or serve as a backbone for the generation of radiation over a broad range of the electromagnetic spectrum. This paper describes the development of a compact sub-Mega-electronvolt (sub-MeV) electron-source setup capable of operating at MHz repetition rates and forming sub-picosecond electron bunches with transverse emittance below 20~nm. The setup relies on a conduction-cooled superconducting single-cell resonator with its geometry altered to enhance the field at the surface of the emitter. The system is designed to accommodate cooling using a model a $2$~W at 4.2 K pulse tube cryogen-free cryocooler. Although we focus on the case of a photoemitted electron bunch, the scheme could be adapted to other emission mechanisms.
Attosecond pulses, produced through high-order harmonic generation in gases, have been successfully used for observing ultrafast, sub-femtosecond electron dynamics in atoms, molecules and solid state systems. Todays typical attosecond sources, however, are often impaired by their low repetition rate and the resulting insufficient statistics, especially when the number of detectable events per shot is limited. This is the case for experiments where several reaction products must be detected in coincidence, and for surface science applications where space-charge effects compromise spectral and spatial resolution. In this work, we present an attosecond light source operating at 200 kHz, which opens up the exploration of phenomena previously inaccessible to attosecond interferometric and spectroscopic techniques. Key to our approach is the combination of a high repetition rate, few-cycle laser source, a specially designed gas target for efficient high harmonic generation, a passively and actively stabilized pump-probe interferometer and an advanced 3D photoelectron/ion momentum detector. While most experiments in the field of attosecond science so far have been performed with either single attosecond pulses or long trains of pulses, we explore the hitherto mostly overlooked intermediate regime with short trains consisting of only a few attosecond pulses.e also present the first coincidence measurement of single-photon double ionization of helium with full angular resolution, using an attosecond source. This opens up for future studies of the dynamic evolution of strongly correlated electrons.
We propose and numerically validate an all-optical scheme to generate optical pulse trains with varying temporal pulse-to-pulse delay and pulse duration. Applying a temporal sinusoidal phase modulation followed by a shaping of the spectral phase enables us to maintain high-quality Gaussian temporal profiles.
We experimentally demonstrate that the transmission of a 1030~nm, 1.3~ps laser beam of 100 mJ energy through fog increases when its repetition rate increases to the kHz range. Due to the efficient energy deposition by the laser filaments in the air, a shockwave ejects the fog droplets from a substantial volume of the beam, at a moderate energy cost. This process opens prospects for applications requiring the transmission of laser beams through fogs and clouds.
Log in to be able to interact and post comments
comments
Fetching comments
Sign in to be able to follow your search criteria
