اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدImpact of Junction Depth and Abruptness on the Activation and the Leakage Current in Germanium n$^{+}$/p Junctions
64
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
The phosphorous activation in Ge n$^{+}$/p junctions is compared in terms of junction depth, by using laser spike annealing at 860{deg}C for 400$mu$s. The reverse junction leakage is found to strongly depend on the abruptness of dopant profiles. A shallow and abrupt junction is shown to have lower phosphorous activation level, due to surface dose loss, and higher band-to-band tunneling (BTBT) leakage, when compared to the deep junction. Simulations were carried out to evaluate the lowest achievable OFF-state currents (I$_{OFF}$) for Ge double-gate FETs when using such an abrupt junction. Our results indicate that a Ge body thickness smaller than 5 nm is required to suppress the BTBT leakage and meet the requirement for the high performance devices defined by the International Technology Roadmap for Semiconductors (I$_{OFF}$ = 10$^{-7}$ A/$mu$m).
قيم البحث
اقرأ أيضاً
Sufficiently large depletion region for photocarrier generation and separation is a key factor for two-dimensional material optoelectronic devices, but few device configurations has been explored for a deterministic control of a space charge region a
rea in graphene with convincing scalability. Here we investigate a graphene-silicon p-i-n photodiode defined in a foundry processed planar photonic crystal waveguide structure, achieving visible - near-infrared, zero-bias and ultrafast photodetection. Graphene is electrically contacting to the wide intrinsic region of silicon and extended to the p an n doped region, functioning as the primary photocarrier conducting channel for electronic gain. Graphene significantly improves the device speed through ultrafast out-of-plane interfacial carrier transfer and the following in-plane built-in electric field assisted carrier collection. More than 50 dB converted signal-to-noise ratio at 40 GHz has been demonstrated under zero bias voltage, with quantum efficiency could be further amplified by hot carrier gain on graphene-i Si interface and avalanche process on graphene-doped Si interface. With the device architecture fully defined by nanomanufactured substrate, this study is the first demonstration of post-fabrication-free two-dimensional material active silicon photonic devices.
The thermodynamic limit of photovoltaic efficiency for a single-junction solar cell can be readily predicted using the bandgap of the active light absorbing material. Such an approach overlooks the energy loss due to non-radiative electron-hole proce
sses. We propose a practical ab initio procedure to determine the maximum efficiency of a thin-film solar cell that takes into account both radiative and non-radiative recombination. The required input includes the frequency-dependent optical absorption coefficient, as well as the capture cross-sections and equilibrium populations of point defects. For kesterite-structured Cu$_2$ZnSnS$_4$, the radiative limit is reached for a film thickness of around 2.6 micrometer, where the efficiency gain due to light absorption is counterbalanced by losses due to the increase in recombination current.
Transition metal dichalcogenide (TMD) materials have emerged as promising candidates for thin film solar cells due to their wide bandgap range across the visible wavelengths, high absorption coefficient and ease of integration with both arbitrary sub
strates as well as conventional semiconductor technologies. However, reported TMD-based solar cells suffer from relatively low external quantum efficiencies (EQE) and low open circuit voltage due to unoptimized design and device fabrication. This paper studies $Pt/WSe_2$ vertical Schottky junction solar cells with various $WSe_2$ thicknesses in order to find the optimum absorber thickness.Also, we show that the photovoltaic performance can be improved via $Al_2O_3$ passivation which increases the EQE by up to 29.5% at 410 nm wavelength incident light. The overall resulting short circuit current improves through antireflection coating, surface doping, and surface trap passivation effects. Thanks to the ${Al_2O_3}$ coating, this work demonstrates a device with open circuit voltage ($V_{OC}$) of 380 mV and short circuit current density ($J_{SC}$) of 10.7 $mA/cm^2$. Finally, the impact of Schottky barrier height inhomogeneity at the $Pt/WSe_2$ contact is investigated as a source of open circuit voltage lowering in these devices
Pyroelectric energy converter is a functional capacitor using pyroelectric material as the dielectric layer. Utilizing the first-order phase transformation of the material, the pyroelectric device can generate adequate electricity within small temper
ature fluctuations. However, most pyroelectric capacitors are leaking during energy conversion. In this paper, we analyze the thermodynamics of pyroelectric energy conversion with consideration of the electric leakage. Our thermodynamic model is verified by experiments using three phase-transforming ferroelectric materials with different pyroelectric properties and leakage behaviors. We demonstrate that the impact of leakage for electric generation is prominent, and sometimes may be confused with the actual power generation by pyroelectricity. We discover an ideal material candidate, (Ba,Ca)(Ti,Zr,Ce)O$_3$, which exhibits large pyroelectric current and extremely low leakage current. The pyroelectric converter made of this material generates 1.95 $mu$A/cm$^2$ pyroelectric current density and 0.2 J/cm$^3$ pyroelectric work density even after 1389 thermodynamic conversion cycles.
Negative refraction usually demands complex structure engineering while it is very natural for massless Dirac fermions (MDFs) across the textit{p-n} junction, this leads to Dirac electron optics. The emergent Dirac materials may exhibit hitherto unid
entified phenomenon due to their nontrivial band structures in contrast to the isotropic MDFs in graphene. Here, as a specific example, we explore the negative refraction induced caustics and Veselago focusing of tilted MDFs across 8-textit{Pmmn} borophene textit{p-n} junctions. To this aim, we develop a technique to effectively construct the electronic Greens function in textit{p-n} junctions with arbitrary junction directions. Based on analytical discussions and numerical calculations, we demonstrate the strong dependence of interference pattern on the junction direction. As the junction direction perpendicular to the tilt direction, Veselago focusing or normal caustics (similar to that in graphene) appears resting on the doping configuration of the textit{p-n} junctions, otherwise anomalous caustics (different from that in graphene) occurs which is manipulated by the junction direction and the doping configuration. Finally, the developed Greens function technique is generally promising to uncover the unique transport of emergent MDFs, and the discovered anomalous caustics makes tilted MDFs potential applications in Dirac electron optics.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
