اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدImpact of Leakage for Electricity Generation by Pyroelectric Converter
72
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
Pyroelectric energy converter is a functional capacitor using pyroelectric material as the dielectric layer. Utilizing the first-order phase transformation of the material, the pyroelectric device can generate adequate electricity within small temperature fluctuations. However, most pyroelectric capacitors are leaking during energy conversion. In this paper, we analyze the thermodynamics of pyroelectric energy conversion with consideration of the electric leakage. Our thermodynamic model is verified by experiments using three phase-transforming ferroelectric materials with different pyroelectric properties and leakage behaviors. We demonstrate that the impact of leakage for electric generation is prominent, and sometimes may be confused with the actual power generation by pyroelectricity. We discover an ideal material candidate, (Ba,Ca)(Ti,Zr,Ce)O$_3$, which exhibits large pyroelectric current and extremely low leakage current. The pyroelectric converter made of this material generates 1.95 $mu$A/cm$^2$ pyroelectric current density and 0.2 J/cm$^3$ pyroelectric work density even after 1389 thermodynamic conversion cycles.
قيم البحث
اقرأ أيضاً
Leakage currents through insulators received continuous attention for decades, owing to their importance for a wide range of technologies, and interest in their fundamental mechanisms. This work investigates the leakage currents through atomic layer
deposited (ALD) $Al_2O_3$, grown on $SrTiO_3$. This combination is not only a key building block of oxide electronics, but also a clean system for studying the leakage mechanisms without interfacial layers that form on most of the conventional bottom electrodes. We show how tiny differences in the deposition process can have a dramatic effect on the leakage behavior. Detailed analysis of the leakage behavior rules out Fowler-Nordheim tunneling (FNT) and thermionic emission, and leaves the trap-related mechanisms of trap-assisted tunneling (TAT) and Poole-Frenkel as the likely mechanisms. After annealing the sample in air, the currents are reduced, which is ascribed to transition from trap-based mechanism to FNT, due to the elimination of the traps. The dramatic role of the assumptions regarding the flat-band voltage used for analysis is critically discussed, and the sensitivity of the extracted parameters on this magnitude is quantitatively described. We show that field effect devices based on structures similar to those described here, should be able to modulate $>10^{13} cm^{-2}$ electrons. These results provide general guidelines for reducing and analyzing leakage currents in insulators, and highlight some of the possible approaches and pitfalls in their analysis.
Liquid electricity generator and hydrovoltaic technology have received numerous attentions, which can be divided into horizontal movement generator and vertical movement generator. The horizontal movement generator is limited for powering the integra
ted and miniaturized energy chip as the current output direction is depending on the moving direction of the water droplet, which means a sustainable and continuous direct-current (DC) electricity output can be hardly achieved because of the film of limited length. On the other hand, the existing vertical movement generators include triboelectricity or humidity gradient-based liquid electricity generator, where the liquid or water resource must be sustainably supplied to ensure continuous current output. Herein, we have designed an integratable vertical generator by sandwiching water droplets with semiconductor and metal, such as graphene or aluminum. This generator, named as polarized liquid molecular generator (PLMG), directly converts the lateral kinetic energy of water droplet into vertical DC electricity with an output voltage of up to ~1.0 V from the dynamic water-semiconductor interface. The fundamental discovery of PLMG is related to the non-symmetric structure of liquid molecules, such as water and alcohols, which can be polarized under the guidance of built-in field caused by the Fermi level difference between metal and semiconductor, while the symmetric liquid molecules cannot produce any electricity on the opposite. Integratable PLMG with a large output power of ~90 nW and voltage of ~2.7 V has been demonstrated, meanwhile its small internal resistance of ~250 kilohm takes a huge advantage in resistance matching with the impedance of electron components. The PLMG shows potential application value in the Internet of Things (IoTs) after proper miniaturization and integration.
Solar-driven interfacial steam generation for desalination has attracted broad attention. However, a significant challenge still remains for achieving a higher evaporation rate and high water quality, together with a cost-effective and easy-to-manufa
cture device to provide a feasible solar-driven steam generation system. In this study, a novel ultra-black paint, Black 3.0, serving as a perfect solar absorber is introduced into the hot-pressed melamine foam networks, allowing us to construct an ultra-black (99% absorptance in the solar region) and self-floating evaporation device. The high performing features of effective solar absorptance and salt-rejection capability contribute to a high-to-date evaporation rate of freshwater at 2.48 kg m-2 h-1 under one sun (1 kW m-2). This interfacial solar evaporator has a daily drinkable water yield of 2.8 kg m-2 even in cloudy winter weather and maintains stability in water with a wide range of acidity and alkalinity (pH 1~14). These features will enable the construction of a facilely fabricated, robust, highly-efficient, and cost-effective solar steam generation system for freshwater production.
Defects are generally regarded to have negative impact on carrier recombination, charge-transport and ion migration in perovskite materials, which thus lower the efficiency and stability of perovskite optoelectronic devices. Meanwhile, lots of effort
s which focused on minimizing defects have greatly promoted the application of perovskite materials. Then, can defects be positive in perovskite optoelectronic devices? Herein, relying on in-depth understanding of defect-associated effects in semiconductors, trapping of photo-generated carriers by defects is applied to enlarge photoconductive gain in perovskite photodetector. The record photoconductive gain, gain-bandwidth product and detection limit were achieved in the photodetector. Exceeding the general concept that defects are harmful, we identify a new view that the defects can be positive in perovskite optoelectronic devices.
In the close vicinity of a hot solid, at distances smaller than the thermal wavelength, a strong electromagnetic energy density exists because of the presence of evanescent field. Here we explore the possibility to harvest this energy using graphene-
based pyroelectric conversion devices made with an active layer encapsulated between two graphene field-effect transistors (GFETs) deposited on the source and on the cold sink. By tuning the bias voltage applied to the gates of these transistors, the thermal state and the spontaneous polarization of the active layer can be controlled at kHz frequencies. We demonstrate that the power density generated by these conversion systems can reach 1300 W/m^2 using pyroelectric Ericsson cycles, a value which surpasses the current production capacity of near-field thermophotovoltaic conversion devices by more than five orders of magnitude with low grade heat sources (T<500 K) and small temperature differences (DT~100 K).
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
