اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدTailoring ink-substrate interactions via thin polymeric layers for high-resolution printing
62
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
The surface properties of a substrate are among the most important parameters in the printing technology of functional materials, determining not only the printing resolution but also the stability of the printed features. This paper addresses the wetting difficulties encountered during inkjet printing on homogeneous substrates as a result of improper surface properties. We show that the wetting of a substrate and, consequently, the quality of the printed pattern, can be mediated through the deposition of polymeric layers that are a few nanometers thick. The chemical nature of the polymers determines the surface energy and polarity of the thin layer. Some applications, however, require a rigorous adjustment of the surface properties. We propose a simple and precise method of surface-energy tailoring based on the thermal decomposition of poly(methyl methacrylate) (PMMA) layers. A smooth transition in the wetting occurs when the thickness of the PMMA layer approaches zero, probably due to percolating the underlying surface of the substrate, which enables the inkjet printing of complex structures with a high resolution. In particular, the wetting of three substrate-ink systems was successfully adjusted using the thin polymeric layer: (i) a tantalum-oxide-based ink on indium-tin-oxide-coated glass, (ii) a ferroelectric lead zirconate titanate ink on a platinized silicon substrate, and (iii) a silver nanoparticle ink on an alumina substrate.
قيم البحث
اقرأ أيضاً
We report the fabrication of a low cost, and highly reproducible large scale surface-enhanced Raman spectroscopy substrate using an inkjet-printed Ag nanoparticle ink (AgNI). The AgNI SERS substrates were evaluated for SERS using BPY as a molecular p
robe. The printed AgNI dot arrays exhibit an excellent SERS performance and reproducibility. The batch to batch and spot to spot standard deviation value of less than 10 percent was obtained. The results reveal the reproducibility of the AgNI SERS dot arrays and its potential application for SERS substrates.
Printed electronics rely on the deposition of conductive liquid inks, typically onto polymeric or paper substrates. Among available conductive fillers for use in electronic inks, carbon nanotubes (CNTs) have high conductivity, low density, processabi
lity at low temperatures, and intrinsic mechanical flexibility. However, the electrical conductivity of printed CNT structures has been limited by CNT quality and concentration, and by the need for nonconductive modifiers to make the ink stable and extrudable. This study introduces a polymer-free, printable aqueous CNT ink, and presents the relationships between printing resolution, ink rheology, and ink-substrate interactions. A model is constructed to predict printed feature sizes on impermeable substrates based on Wenzel wetting. Printed lines have conductivity up to 10,000 S/m. The lines are flexible, with < 5% change in DC resistance after 1,000 bending cycles, and <3% change in DC resistance with a bending radius down to 1 mm. Demonstrations focus on (i) conformality, via printing CNTs onto stickers that can be applied to curved surfaces, (ii) interactivity using a CNT-based button printed onto folded paper structure, and (iii) capacitive sensing of liquid wicking into the substrate itself. Facile integration of surface mount components on printed circuits is enabled by the intrinsic adhesion of the wet ink.
Currently, additive manufacturing of ceramics by stereolithography (SLA) is limited to single materials and by a poor thickness resolution that strongly depends on the ceramic particles-UV light interaction. Combining selective laser curing with inkj
et printing represents a novel strategy to overcome these constrains. Nonetheless, this approach requires UV-curable inks that allow hardening of the printed material and sintering to high density. In this work, we report how to design an ink for inkjet printing of yttria stabilized zirconia (YSZ) which can be impressed by addition of UV-curable monomers. We especially show how the formulation of the inks and particularly the UV-monomer concentration impacts the printability and the UV-curing. This leads to prints that are resistant to solvent washing first and densify to 96% dense YSZ layers after sintering.
We report here a quantitative method of Transmission Electron Microscopy (TEM) to measure the shapes, sizes and volumes of nanoparticles which are responsible for their properties. Gold nanoparticles (Au NPs) acting as nucleating agents for the elect
roless deposition of silver NPs on SU-8 polymers were analyzed in this project. The atomic-number contrast (Z-contrast) imaging technique reveals the height and effective diameter of each Au NP and a volume distribution is obtained. Varying the reducing agents produced Au NPs of different sizes which were found both on the polymer surface and in some cases buried several nanometers below the surface. The morphology of Au NPs is an important factor for systems that use surface-bound nanoparticles as nucleation sites as in electroless metallization. Electrolessly deposited silver layers reduced by hydroquinone on SU-8 polymer are analyzed in this project.
Stark deceleration allows for precise control over the velocity of a pulsed molecular beam and, by the nature of its limited phase-space acceptance, reduces the energy width of the decelerated packet. We describe an alternate method of operating a St
ark decelerator that further reduces the energy spread over the standard method of operation. In this alternate mode of operation, we aggressively decelerate the molecular packet using a high phase angle. This technique brings the molecular packet to the desired velocity before it reaches the end of the decelerator; the remaining stages are then used to longitudinally and transversely guide the packet to the detection/interaction region. The result of the initial aggressive slowing is a reduction in the phase-space acceptance of the decelerator and thus a narrowing of the velocity spread of the molecular packet. In addition to the narrower energy spread, this method also results in a velocity spread that is nearly independent of the final velocity. Using the alternate deceleration technique, the energy resolution of molecular collision measurements can be improved considerably.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
