اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدSurface Sensitive NMR Detection of the SEI Layer on Reduced Graphene Oxide
54
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
The solid electrolyte interphase (SEI) is detrimental for rechargeable batteries performance and lifetime. Understanding its formation requires analytical techniques that provide molecular level insight. Here dynamic nuclear polarization (DNP) is utilized for the first time for enhancing the sensitivity of solid state NMR (ssNMR) spectroscopy to the SEI. The approach is demonstrated on reduced-graphene oxide (rGO) cycled in Li-ion cells in natural abundance and 13C-enriched electrolyte solvents. Our results indicate that DNP enhances the signal of outer SEI layers, enabling detection of natural abundance 13C spectra from this component of the SEI at reasonable timeframes. Furthermore, 13C- enriched electrolytes measurements at 100K provide ample sensitivity without DNP due to the vast amount of SEI filling the rGO pores, thereby allowing differentiating the inner and outer SEI layers composition. Developing this approach further will benefit the study of many electrode materials, equipping ssNMR with the needed sensitivity to efficiently probe the SEI.
قيم البحث
اقرأ أيضاً
Silicon anodes promise high energy densities of next-generation lithium-ion batteries, but suffer from shorter cycle life. The accelerated capacity fade stems from the repeated fracture and healing of the solid-electrolyte interphase (SEI) on the sil
icon surface. This interplay of chemical and mechanical effects in SEI on silicon electrodes causes a complex aging behavior. However, so far, no model mechanistically captures the interrelation between mechanical SEI deterioration and accelerated SEI growth. In this article, we present a thermodynamically consistent continuum model of an electrode particle surrounded by an SEI layer. The silicon particle model consistently couples chemical reactions, physical transport, and elastic deformation. The SEI model comprises elastic and plastic deformation, fracture, and growth. Capacity fade measurements and in-situ mechanical SEI measurements provide validation for our model. For the first time, we model the influence of cycling rate on the long-term mechanical SEI deterioration and regrowth. Our model predicts the experimentally observed transition in time dependence from square-root-of-time growth during battery storage to linear-in-time growth during continued cycling. Thereby our model unravels the mechanistic dependence of battery aging on operating conditions and supports the efforts to prolong the battery life of next-generation lithium-ion batteries.
Incorporation of magnetism in graphene based compounds holds great promise for potential spintronic applications. By optimizing point defects and high edge density of defects, we report many-fold increase in the ferromagnetic saturation moment in lac
ey reduced graphene oxide nanoribbons (LRGONR) as compared to other graphene derivatives. The samples were synthesized using chemical unzipping methodology. Detailed structural and morphological characterizations are discussed that include XRD, Raman, SEM, HRTEM and XPS measurements. Brilluoin function analysis to magnetization data reflects best fit for J = 7/2 with a saturation moment of 1.1 emu/g. The microscopic origin of magnetization in LRGONR is assigned to high edge defect density which has also been correlated to microstructure.
Graphene oxide can be used as a precursor to graphene but the quality of graphene flakes is highly heterogeneous. Scanning-Raman-Microscopy (SRM) is used to characterize films of graphene derived from flakes of graphene oxide with an almost intact ca
rbon framework (ai-GO). The defect density of these flakes is visualized in detail by analyzing the intensity and full-width at half-maximum of the most pronounced Raman peaks. In addition, we superimpose the SRM results with AFM images and correlate the spectroscopic results with the morphology. Furthermore, we use SRM technique to display the amount of defects in a film of graphene. Thus, an area of 250 x 250 {my}m2 of graphene is probed with a step-size increment of 1 {mu}m. We are able to visualize the position of graphene flakes, edges and the substrate. Finally, we alter parameters of measurement to analyze the quality of graphene fast and reliable. The described method can be used to probe and visualize the quality of graphene films.
In this paper, a method is presented to create and characterize mechanically robust, free standing, ultrathin, oxide films with controlled, nanometer-scale thickness using Atomic Layer Deposition (ALD) on graphene. Aluminum oxide films were deposited
onto suspended graphene membranes using ALD. Subsequent etching of the graphene left pure aluminum oxide films only a few atoms in thickness. A pressurized blister test was used to determine that these ultrathin films have a Youngs modulus of 154 pm 13 GPa. This Youngs modulus is comparable to much thicker alumina ALD films. This behavior indicates that these ultrathin two-dimensional films have excellent mechanical integrity. The films are also impermeable to standard gases suggesting they are pinhole-free. These continuous ultrathin films are expected to enable new applications in fields such as thin film coatings, membranes and flexible electronics.
In this study, we use our recently prepared graphene oxide (GO) with an almost intact {sigma}-framework of C-atoms (ai-GO) to probe the thermal stability of the carbon framework for the first time. Ai-GO exhibits few defects only by preventing CO2 fo
rmation during synthesis. Ai-GO was thermally treated before chemical reduction and subsequently the resulting defect density in graphene was determined by statistical Raman microscopy. Surprisingly, the carbon framework of ai-GO is stable in thin films up to 100 {deg}C. Furthermore, we find evidence for an increasing quality of ai-GO upon annealing at 50 {deg}C before reduction. The carbon framework of GO prepared according to the popular Hummers method (GO-c)appears to be less stable and decomposition starts at 50 {deg}C what is qualitatively indicated by CO2-trapping experiments in {mu}m-thin films. Information about the stability of GO is important for storing, processing and applying GO in applications.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
