اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدDispersive shallow water wave modelling. Part II: Numerical simulation on a globally flat space
117
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
In this paper, we describe a numerical method to solve numerically the weakly dispersive fully nonlinear Serre-Green-Naghdi (SGN) celebrated model. Namely, our scheme is based on reliable finite volume methods, proven to be very effective for the hyperbolic part of equations. The particularity of our study is that we develop an adaptive numerical model using moving grids. Moreover, we use a special form of the SGN equations where non-hydrostatic part of pressure is found by solving a nonlinear elliptic equation. Moreover, this form of governing equations allows determining the natural form of boundary conditions to obtain a well-posed (numerical) problem.
قيم البحث
اقرأ أيضاً
In the present manuscript, we consider the problem of dispersive wave simulation on a rotating globally spherical geometry. In this Part IV, we focus on numerical aspects while the model derivation was described in Part III. The algorithm we propose
is based on the splitting approach. Namely, equations are decomposed on a uniformly elliptic equation for the dispersive pressure component and a hyperbolic part of shallow water equations (on a sphere) with source terms. This algorithm is implemented as a two-step predictor-corrector scheme. On every step, we solve separately elliptic and hyperbolic problems. Then, the performance of this algorithm is illustrated on model idealised situations with an even bottom, where we estimate the influence of sphericity and rotation effects on dispersive wave propagation. The dispersive effects are quantified depending on the propagation distance over the sphere and on the linear extent of generation region. Finally, the numerical method is applied to a couple of real-world events. Namely, we undertake simulations of the Bulgarian 2007 and Chilean 2010 tsunamis. Whenever the data is available, our computational results are confronted with real measurements.
The turbulent boundary layer over a flat plate is computed by direct numerical simulation (DNS) of the incompressible Navier-Stokes equations as a test bed for a synthetic turbulence generator (STG) inflow boundary condition. The inlet momentum thick
ness Reynolds number is approximately 1,000. The study provides validation of the ability of the STG to develop accurate turbulence in 5 to 7 boundary layer thicknesses downstream of the boundary condition. Also tested was the effect of changes in the stabilization scheme on the development of the boundary layer. Moreover, the grid resolution required for both the development region and the downstream flow is investigated when using a stabilized finite element method.
Cardiovascular diseases, specifically cerebral aneurysms, represent a major cause of morbidity and mortality, having a significant impact on the cost and overall status of health care. In the present work, we employ a haemorheological blood model ori
ginally proposed by Owens to investigate the haemodynamics of blood flow through an aneurytic channel. This constitutive equation for whole human blood is derived using ideas drawn from temporary polymer network theory to model the aggregation and disaggregation of erythrocytes in normal human blood at different shear rates. To better understand the effect of rheological models on the haemodynamics of blood flow in cerebral aneurysms we compare our numerical results with those obtained with other rheological models such as the Carreau-Yasuda (C-Y) model. The results show that the velocity profiles for the Newtonian and the Owens models are approximately similar but differ from those of the C-Y model. In order to stabilize our numerical simulations, we propose two new stabilization techniques, the so-called N-Owens and I-Owens methods. Employing the N-Owens stabilization method enables us to capture the effect of erythrocyte aggregation in blood flow through a cerebral aneurysm at higher Weissenberg (We) and Reynolds (Re) numbers than would otherwise be possible.
The efficient mixing of fluids is key in many applications, such as chemical reactions and nanoparticle precipitation. Detailed experimental measurements of the mixing dynamics are however difficult to obtain, and so predictive numerical tools are he
lpful in designing and optimizing many processes. If two different fluids are considered, the viscosity and density of the mixture depend often nonlinearly on the composition, which makes the modeling of the mixing process particularly challenging. Hence water-water mixtures in simple geometries such as T-mixers have been intensively investigated, but little is known about the dynamics of more complex mixtures, especially in the turbulent regime. We here present a numerical method allowing the accurate simulation of two-fluid mixtures. Using a high-performance implementation of this method we perform direct numerical simulations resolving the spatial and temporal dynamics of water-ethanol flows for Reynolds numbers from 100 to 2000. The flows states encountered during turbulence transition and their mixing properties are discussed in detail and compared to water-water mixtures.
A formulation of the shallow water equations adapted to general complex terrains is proposed. Its derivation starts from the observation that the typical approach of depth integrating the Navier-Stokes equations along the direction of gravity forces
is not exact in the general case of a tilted curved bottom. We claim that an integration path that better adapts to the shallow water hypotheses follows the cross-flow surface, i.e., a surface that is normal to the velocity field at any point of the domain. Because of the implicitness of this definition, we approximate this cross-flow path by performing depth integration along a local direction normal to the bottom surface, and propose a rigorous derivation of this approximation and its numerical solution as an essential step for the future development of the full cross-flow integration procedure. We start by defining a local coordinate system, anchored on the bottom surface to derive a covariant form of the Navier-Stokes equations. Depth integration along the local normals yields a covariant version of the shallow water equations, which is characterized by flux functions and source terms that vary in space because of the surface metric coefficients and related derivatives. The proposed model is discretized with a first order FORCE-type Godunov Finite Volume scheme that allows implementation of spatially variable fluxes. We investigate the validity of our SW model and the effects of the bottom geometry by means of three synthetic test cases that exhibit non negligible slopes and surface curvatures. The results show the importance of taking into consideration bottom geometry even for relatively mild and slowly varying curvatures.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
