ترغب بنشر مسار تعليمي؟ اضغط هنا

Dechirper Wakefields for Short Bunches

169   0   0.0 ( 0 )
 نشر من قبل Karl Bane
 تاريخ النشر 2016
  مجال البحث فيزياء
والبحث باللغة English




اسأل ChatGPT حول البحث

In previous work [1] general expressions, valid for arbitrary bunch lengths, were derived for the wakefields of corrugated structures with flat geometry, such as is used in the RadiaBeam/LCLS dechirper. However, the bunch at the end of linac-based X-ray FELs--like the LCLS--is extremely short, and for short bunches the wakes can be considerably simplified. In this work, we first derive analytical approximations to the short-range wakes. These are generalized wakes, in the sense that their validity is not limited to a small neighborhood of the symmetry axis, but rather extends to arbitrary transverse offsets of driving and test particles. The validity of these short-bunch wakes holds not only for the corrugated structure, but rather for any flat structure whose beam-cavity interaction can be described by a surface impedance. We use these wakes to obtain, for a short bunch passing through a dechirper: estimates of the energy loss as function of gap, the transverse kick as function of beam offset, the slice energy spread increase, and the emittance growth. In the Appendix, a more accurate derivation--than is found in [1]--of the arbitrary bunch length wakes is performed; we find full agreement with the earlier results, provided the bunches are short compared to the dechirper gap, which is normally the regime of interest. [1] K. Bane and G. Stupakov, Phys. Rev. ST Accel. Beams 18, 034401(2015).



قيم البحث

اقرأ أيضاً

We give formulas for the longitudinal, transverse, and quad point charge wakes for a short bunch of electrons passing by one plate of a flat dechirper.
64 - Igor Zagorodnov 2018
We discuss several analytical models for impedances of very short bunches. The approximate analytical models are compared with direct solution of Maxwells equations.
We develop analytical models of the longitudinal and transverse wakes, on and off axis for realistic structures, and then compare them with numerical calculations, and generally find good agreement. These analytical first order formulas approximate t he droop at the origin of the longitudinal wake and of the slope of the transverse wakes; they represent an improvement in accuracy over earlier, zeroth order formulas. In example calculations for the RadiaBeam/LCLS dechirper using typical parameters, we find a 16% droop in the energy chirp at the bunch tail compared to simpler calculations. With the beam moved to 200~$mu$m from one jaw in one dechiper section, one can achieve a 3~MV transverse kick differential over a 30~$mu$m length.
Temporally-modulated electron beams have a wide array of applications ranging from the generation of coherently-enhanced electromagnetic radiation to the resonant excitation of electromagnetic wakefields in advanced-accelerator concepts. Likewise pro ducing low-energy ultrashort microbunches could be useful for ultra-fast electron diffraction and new accelerator-based light-source concepts. In this Letter we propose and experimentally demonstrate a passive microbunching technique capable of forming a picosecond bunch train at $sim 6$~MeV. The method relies on the excitation of electromagnetic wakefields as the beam propagates through a dielectric-lined waveguide. Owing to the non-ultrarelativistic nature of the beam, the induced energy modulation eventually converts into a density modulation as the beam travels in a following free-space drift. The modulated beam is further accelerated to $sim20$~MeV while preserving the imparted density modulation.
One of the key-issues to increase the luminosity in the next generation particle factories is to reduce the bunch length at the interaction point (IP) as much as possible. This will allow reducing proportionally the transverse beta functions at the I P and increasing the luminosity by the same factor. The strong RF focusing consists in obtaining short bunches by substantially increasing the lattice momentum compaction and the RF gradient. In this regime the bunch length is modulated along the ring and could be minimized at the IP. If the principal impedance generating elements of the ring are located where the bunch is long (in the RF cavities region) it is possible to avoid microwave instability and excessive bunch lengthening due to the potential well distortion.
التعليقات
جاري جلب التعليقات جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
mircosoft-partner

هل ترغب بارسال اشعارات عن اخر التحديثات في شمرا-اكاديميا