اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدCapillary filling using Lattice Boltzmann Equations: the case of multi-phase flows
98
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
We present a systematic study of capillary filling for multi-phase flows by using mesoscopic lattice Boltzmann models describing a diffusive interface moving at a given contact angle with respect to the walls. We compare the numerical results at changing the density ratio between liquid and gas phases and the ratio between the typical size of the capillary and the interface width. It is shown that numerical results yield quantitative agreement with the Washburn law when both ratios are large, i.e. as the hydrodynamic limit of a infinitely thin interface is approached. We also show that in the initial stage of the filling process, transient behaviour induced by inertial effects and ``vena contracta mechanisms, may induce significant departure from the Washburn law. Both effects are under control in our lattice Boltzmann equation and in good agreement with the phenomenology of capillary filling.
قيم البحث
اقرأ أيضاً
We present a systematic study of capillary filling for a binary fluid by using mesoscopic a lattice Boltzmann model describing a diffusive interface moving at a given contact angle with respect to the walls. We compare the numerical results at changi
ng the ratio the typical size of the capillary, H, and the wettability of walls. Numerical results yield quantitative agreement with the Washburn law in all cases, provided the channel lenght is sufficiently larger then the interface width. We also show that in the initial stage of the filling process, transient behaviour induced by inertial effects are under control in our lattice Boltzmann equation and in good agreement with the phenomenology of capillary filling. Finally, at variance with multiphase LB simulations, velocity and pressure profiles evolve under the sole effect of capillary drive all along the channel.
Numerical simulations of two-dimensional capillary filling using the pseudo-potential lattice Boltzmann model for multiphase fluids are presented, with special emphasis on the role of finite-vapour density effects. It is shown that whenever the densi
ty of the light-phase exceeds about ten percent of the dense phase, the front motion proceeds through a combined effect of capillary advection and condensation. As a result, under these conditions, the front proceeds at a higher speed as compared to the Washburn prediction. It is suggested that such an acceleration effect might be observed in experiments performed sufficiently close to critical conditions
In this paper, we develop an efficient lattice Boltzmann (LB) model for simulating immiscible incompressible $N$-phase flows $(N geq 2)$ based on the Cahn-Hilliard phase field theory. In order to facilitate the design of LB model and reduce the calcu
lation of the gradient term, the governing equations of the $N$-phase system are reformulated, and they satisfy the conservation of mass, momentum and the second law of thermodynamics. In the present model, $(N-1)$ LB equations are employed to capture the interface, and another LB equation is used to solve the Navier-Stokes (N-S) equations, where a new distribution function for the total force is delicately designed to reduce the calculation of the gradient term. The developed model is first validated by two classical benchmark problems, including the tests of static droplets and the spreading of a liquid lens, the simulation results show that the current LB model is accurate and efficient for simulating incompressible $N$-phase fluid flows. To further demonstrate the capability of the LB model, two numerical simulations, including dynamics of droplet collision for four fluid phases and dynamics of droplets and interfaces for five fluid phases, are performed to test the developed model. The results show that the present model can successfully handle complex interactions among $N$ ($N geq 2$) immiscible incompressible flows.
In this brief report, a thermal lattice-Boltzmann (LB) model is presented for axisymmetric thermal flows in the incompressible limit. The model is based on the double-distribution-function LB method, which has attracted much attention since its emerg
ence for its excellent numerical stability. Compared with the existing axisymmetric thermal LB models, the present model is simpler and retains the inherent features of the standard LB method. Numerical simulations are carried out for the thermally developing laminar flows in circular ducts and the natural convection in an annulus between two coaxial vertical cylinders. The Nusselt number obtained from the simulations agrees well with the analytical solutions and/or the results reported in previous studies.
We show how the capillary filling of microchannels is affected by posts or ridges on the sides of the channels. Ridges perpendicular to the flow direction introduce contact line pinning which slows, or sometimes prevents, filling; whereas ridges para
llel to the flow provide extra surface which may enhances filling. Patterning the microchannel surface with square posts has little effect on the ability of a channel to fill for equilibrium contact angle $theta_e lesssim 30^{mathrm{o}}$. For $theta_e gtrsim 60^{mathrm{o}}$, however, even a small number of posts can pin the advancing liquid front.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
