ترغب بنشر مسار تعليمي؟ اضغط هنا

Conditionally rigorous mitigation of multiqubit measurement errors

163   0   0.0 ( 0 )
 نشر من قبل Michael R. Geller
 تاريخ النشر 2021
  مجال البحث فيزياء
والبحث باللغة English
 تأليف Michael R. Geller




اسأل ChatGPT حول البحث

Several techniques have been recently introduced to mitigate errors in near-term quantum computers without the overhead required by quantum error correcting codes. While most of the focus has been on gate errors, measurement errors are significantly larger than gate errors on some platforms. A widely used {it transition matrix error mitigation} (TMEM) technique uses measured transition probabilities between initial and final classical states to correct subsequently measured data. However from a rigorous perspective, the noisy measurement should be calibrated with perfectly prepared initial states and the presence of any state-preparation error corrupts the resulting mitigation. Here we develop a measurement error mitigation technique, conditionally rigorous TMEM, that is not sensitive to state-preparation errors and thus avoids this limitation. We demonstrate the importance of the technique for high-precision measurement and for quantum foundations experiments by measuring Mermin polynomials on IBM Q superconducting qubits. An extension of the technique allows one to correct for both state-preparation and measurement (SPAM) errors in expectation values as well; we illustrate this by giving a protocol for fully SPAM-corrected quantum process tomography.

قيم البحث

اقرأ أيضاً

State preparation and measurement (SPAM) errors limit the performance of near-term quantum computers and their potential for practical application. SPAM errors are partly correctable after a calibration step that requires, for a complete implementati on on a register of $n$ qubits, $2^n$ additional measurements. Here we introduce an approximate but efficient method for multiqubit SPAM error characterization and mitigation requiring the classical processing of $2^n ! times 2^n$ matrices, but only $O(4^k n^2)$ measurements, where $k=O(1)$ is the number of qubits in a correlation volume. We demonstrate and validate the technique using an IBM Q processor on registers of 4 and 8 superconducting qubits.
126 - Michael R. Geller 2020
We review an experimental technique used to correct state preparation and measurement errors on gate-based quantum computers, and discuss its rigorous justification. Within a specific biased quantum measurement model, we prove that nonideal measureme nt of an arbitrary $n$-qubit state is equivalent to ideal projective measurement followed by a classical Markov process $Gamma$ acting on the output probability distribution. Measurement errors can be removed, with rigorous justification, if $Gamma$ can be learned and inverted. We show how to obtain $Gamma$ from gate set tomography (R. Blume-Kohout et al., arXiv:1310.4492) and apply the error correction technique to single IBM Q superconducting qubits.
Dynamical decoupling (DD) is a widely-used quantum control technique that takes advantage of temporal symmetries in order to partially suppress quantum errors without the need resource-intensive error detection and correction protocols. This and othe r open-loop error mitigation techniques are critical for quantum information processing in the era of Noisy Intermediate-Scale Quantum technology. However, despite its utility, dynamical decoupling does not address errors which occur at unstructured times during a circuit, including certain commonly-encountered noise mechanisms such as cross-talk and imperfectly calibrated control pulses. Here, we introduce and demonstrate an alternative technique - `quantum measurement emulation (QME) - that effectively emulates the measurement of stabilizer operators via stochastic gate application, leading to a first-order insensitivity to coherent errors. The QME protocol enables error suppression based on the stabilizer code formalism without the need for costly measurements and feedback, and it is particularly well-suited to discrete coherent errors that are challenging for DD to address.
Variational Quantum Algorithms (VQAs) are a promising application for near-term quantum processors, however the quality of their results is greatly limited by noise. For this reason, various error mitigation techniques have emerged to deal with noise that can be applied to these algorithms. Recent work introduced a technique for mitigating expectation values against correlated measurement errors that can be applied to measurements of 10s of qubits. We apply these techniques to VQAs and demonstrate its effectiveness in improving estimates to the cost function. Moreover, we use the data resulting from this technique to experimentally characterize measurement errors in terms of the device connectivity on devices of up to 20 qubits. These results should be useful for better understanding the near-term potential of VQAs as well as understanding the correlations in measurement errors on large, near-term devices.
79 - Lin Chen , Yi-Xin Chen 2007
We introduce a feasible method of constructing the entanglement witness that detects the genuine entanglement of a given pure multiqubit state. We illustrate our method in the scenario of constructing the witnesses for the multiqubit states that are broadly theoretically and experimentally investigated. It is shown that our method can construct the effective witnesses for experiments. We also investigate the entanglement detection of symmetric states and mixed states.
التعليقات
جاري جلب التعليقات جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
mircosoft-partner

هل ترغب بارسال اشعارات عن اخر التحديثات في شمرا-اكاديميا