اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدLarge-Size Free-Standing Single-crystal b-Ga2O3 Membranes Fabricated by Hydrogen Implantation and Lift-Off
78
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
In this paper, we have demonstrated the large-size free-standing single-crystal b-Ga2O3 NMs fabricated by the hydrogen implantation and lift-off process directly from MOCVD grown b-Ga2O3 epifilms on native substrates. The optimum implantation conditions were simulated with a Monte-Carlo simulation to obtain the high hydrogen concentration with a narrow ion distribution at the desired depth. Two as grown b-Ga2O3 samples with different orientation ([100] and [001]) were used and successfully create 1.2 um thick b-Ga2O3 NMs without any physical damages. These b-Ga2O3 NMs were then transfer-printed onto rigid and flexible substrates such as SiC substrate and polyimide substrate. Various material characterizations were performed to investigate the crystal quality, surface morphology, optical property, mechanical property, and bandgap before and after the lift-off and revealed that good material quality is maintained. This result offers several benefits in that the thickness, doping, and size of b-Ga2O3 NMs can be fully controlled. Moreover, more advanced b-Ga2O3-based NM structures such as (AlxGa1-x)2O3/Ga2O3 heterostructure NMs can be directly created from their bulk epitaxy substrates thus this result provides a viable route for the realization of high performance b-Ga2O3 NM-based electronics and optoelectronics that can be built on various substrates and platforms.
قيم البحث
اقرأ أيضاً
A method for obtaining a smooth, single crystal diamond surface is presented, whereby a sacrificial defective layer is created by implantation and graphitized by annealing before being selectively etched. We have used O+ at 240 keV, the main process
variables being the ion fluence (ranging from 3x10^15 cm^-2 to 3x10^17 cm^-2) and the final etching process (wet etch, H2 plasma and annealing in air). The substrates were characterized by atomic force microscopy, optical profilometry and white beam X-ray topography. The influence of the various process parameters on the resulting lift-off efficiency and final surface roughness is discussed. An O+ fluence of 2x10^17 cm^-2 was found to result in sub-nanometre roughness over tens of um^2.
Free-standing nanoribbons of InAs quantum membranes (QMs) transferred onto a (Si/Mo) multilayer mirror substrate are characterized by hard x-ray photoemission spectroscopy (HXPS), and by standing-wave HXPS (SW-HXPS). Information on the chemical compo
sition and on the chemical states of the elements within the nanoribbons was obtained by HXPS and on the quantitative depth profiles by SW-HXPS. By comparing the experimental SW-HXPS rocking curves to x-ray optical calculations, the chemical depth profile of the InAs(QM) and its interfaces were quantitatively derived with angstrom precision. We determined that: i) the exposure to air induced the formation of an InAsO$_4$ layer on top of the stoichiometric InAs(QM); ii) the top interface between the air-side InAsO$_4$ and the InAs(QM) is not sharp, indicating that interdiffusion occurs between these two layers; iii) the bottom interface between the InAs(QM) and the native oxide SiO$_2$ on top of the (Si/Mo) substrate is abrupt. In addition, the valence band offset (VBO) between the InAs(QM) and the SiO$_2$/(Si/Mo) substrate was determined by HXPS. The value of $VBO = 0.2 pm 0.04$ eV is in good agreement with literature results obtained by electrical characterization, giving a clear indication of the formation of a well-defined and abrupt InAs/SiO$_2$ heterojunction. We have demonstrated that HXPS and SW-HXPS are non-destructive, powerful methods for characterizing interfaces and for providing chemical depth profiles of nanostructures, quantum membranes, and 2D layered materials.
Quasi-free standing epitaxial graphene is obtained on SiC(0001) by hydrogen intercalation. The hydrogen moves between the 6root3 reconstructed initial carbon layer and the SiC substrate. The topmost Si atoms which for epitaxial graphene are covalentl
y bound to this buffer layer, are now saturated by hydrogen bonds. The buffer layer is turned into a quasi-free standing graphene monolayer with its typical linear pi-bands. Similarly, epitaxial monolayer graphene turns into a decoupled bilayer. The intercalation is stable in air and can be reversed by annealing to around 900 degrees Celsius.
The origin of the unusual 90^o ferroelectric / ferroelastic domains, consistently observed in recent studies on meso and nanoscale free-standing single crystals of BaTiO3 [Schilling et al., Physical Review B, 74, 024115 (2006); Schilling et al., Nano
Letters, 7, 3787 (2007)], has been considered. A model has been developed which postulates that the domains form as a response to elastic stress induced by a surface layer which does not undergo the paraelectric-ferroelectric, cubic-tetragonal phase transition. This model was found to accurately account for the changes in domain periodicity as a function of size that had been observed experimentally. The physical origin of the surface layer might readily be associated with patterning damage, seen in experiment; however, when all evidence of physical damage is removed from the BaTiO3 surfaces by thermal annealing, the domain configuration remains practically unchanged. This suggests a more intrinsic origin, such as the increased importance of surface tension at small dimensions. The effect of surface tension is also shown to be proportional to the difference in hardness between the surface and the interior of the ferroelectric. The present model for surface tension induced twinning should also be relevant for finely grained or core-shell structured ceramics.
In-situ etching using Ga flux in an ultra-high vacuum environment like MBE is introduced as a method to make high aspect ratio 3 dimensional structures in $beta$-Ga2O3. Etching of $beta$-Ga2O3 due to excess Ga adatoms on the epilayer surface had been
viewed as non-ideal for epitaxial growth especially since it results in plateauing and lowering of growth rate. In this study, we use this well-known reaction from epitaxial growth to intentionally etch $beta$-Ga2O3. We demonstrate etch rate ranging from 2.9 nm/min to 30 nm/min with the highest reported etch rate being only limited by the highest Ga flux used. Patterned in-situ etching is also demonstrated and used to study the effect of fin orientation on the sidewall profiles and dopant (Si) segregation on the etched surface. Using in-situ Ga etching, we also demonstrate 150 nm wide fins and 200 nm wide nano pillars with high aspect ratio. This new etching method could enable future development of highly scaled vertical and lateral 3D devices in $beta$-Ga2O3.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
