اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدCooperative Multi-Point Vehicular Positioning Using Millimeter-Wave Surface Reflection (Extended version)
69
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
Multi-point vehicular positioning is one essential operation for autonomous vehicles. However, the state-of-the-art positioning technologies, relying on reflected signals from a target (i.e., RADAR and LIDAR), cannot work without line-of-sight. Besides, it takes significant time for environment scanning and object recognition with potential detection inaccuracy, especially in complex urban situations. Some recent fatal accidents involving autonomous vehicles further expose such limitations. In this paper, we aim at overcoming these limitations by proposing a novel relative positioning approach, called Cooperative Multi-point Positioning (COMPOP). The COMPOP establishes cooperation between a target vehicle (TV) and a sensing vehicle (SV) if a LoS path exists, where a TV explicitly lets an SV to know the TVs existence by transmitting positioning waveforms. This cooperation makes it possible to remove the time-consuming scanning and target recognizing processes, facilitating real-time positioning. One prerequisite for the cooperation is a clock synchronization between a pair of TV and SV. To this end, we use a phase-differential-of-arrival based approach to remove the TV-SV clock difference from the received signal. With clock difference correction, the TVs position can be obtained via peak detection over a 3D power spectrum constructed by a Fourier transform (FT) based algorithm. The COMPOP also incorporates nearby vehicles, without knowing their locations, into the above cooperation for the case without a LoS path. The effectiveness of the COMPOP is verified by several simulations concerning practical channel parameters.
قيم البحث
اقرأ أيضاً
Multi-point detection of the full-scale environment is an important issue in autonomous driving. The state-of-the-art positioning technologies (such as RADAR and LIDAR) are incapable of real-time detection without line-of-sight. To address this issue
, this paper presents a novel multi-point vehicular positioning technology via emph{millimeter-wave} (mmWave) transmission that exploits multi-path reflection from a emph{target vehicle} (TV) to a emph{sensing vehicle} (SV), which enables the SV to fast capture both the shape and location information of the TV in emph{non-line-of-sight} (NLoS) under the assistance of multi-path reflections. A emph{phase-difference-of-arrival} (PDoA) based hyperbolic positioning algorithm is designed to achieve the synchronization between the TV and SV. The emph{stepped-frequency-continuous-wave} (SFCW) is utilized as signals for multi-point detection of the TVs. Transceiver separation enables our approach to work in NLoS conditions and achieve much lower latency compared with conventional positioning techniques.
Channel estimation for hybrid Multiple Input Multiple Output (MIMO) systems at Millimeter-Waves (mmW)/sub-THz is a fundamental, despite challenging, prerequisite for an efficient design of hybrid MIMO precoding/combining. Most works propose sequentia
l search algorithms, e.g., Compressive Sensing (CS), that are most suited to static channels and consequently cannot apply to highly dynamic scenarios such as Vehicle-to-Everything (V2X). To address the latter ones, we leverage textit{recurrent vehicle passages} to design a novel Multi Vehicular (MV) hybrid MIMO channel estimation suited for Vehicle-to-Infrastructure (V2I) and Vehicle-to-Network (V2N) systems. Our approach derives the analog precoder/combiner through a MV beam alignment procedure. For the digital precoder/combiner, we adapt the Low-Rank (LR) channel estimation method to learn the position-dependent eigenmodes of the received digital signal (after beamforming), which is used to estimate the compressed channel in the communication phase. Extensive numerical simulations, obtained with ray-tracing channel data and realistic vehicle trajectories, demonstrate the benefits of our solution in terms of both achievable Spectral Efficiency (SE) and Mean Square Error (MSE) compared to the Unconstrained Maximum Likelihood (U-ML) estimate of the compressed digital channel, making it suitable for both 5G and future 6G systems. Most notably, in some scenarios, we obtain the performance of the optimal Fully Digital (FD) systems.
This paper investigates a device-to-device (D2D) cooperative computing system, where an user can offload part of its computation task to nearby idle users with the aid of an intelligent reflecting surface (IRS). We propose to minimize the total compu
ting delay via jointly optimizing the computation task assignment, transmit power, bandwidth allocation, and phase beamforming of the IRS. To solve the formulated problem, we devise an alternating optimization algorithm with guaranteed convergence. In particular, the task assignment strategy is derived in closed-form expression, while the phase beamforming is optimized by exploiting the semi-definite relaxation (SDR) method. Numerical results demonstrate that the IRS enhanced D2D cooperative computing scheme can achieve a much lower computing delay as compared to the conventional D2D cooperative computing strategy.
Millimeter-wave (mmWave) multiple-input multiple-output (MIMO) system for the fifth generation (5G) cellular communications can also enable single-anchor positioning and object tracking due to its large bandwidth and inherently high angular resolutio
n. In this paper, we introduce the newly invented concept, large intelligent surface (LIS), to mmWave positioning systems, study the theoretical performance bounds (i.e., Cramer-Rao lower bounds) for positioning, and evaluate the impact of the number of LIS elements and the value of phase shifters on the position estimation accuracy compared to the conventional scheme with one direct link and one non-line-of-sight path. It is verified that better performance can be achieved with a LIS from the theoretical analyses and numerical study.
The densely packed antennas of millimeter-Wave (mmWave) MIMO systems are often blocked by the rain, snow, dust and even by fingers, which will change the channels characteristics and degrades the systems performance. In order to solve this problem, w
e propose a cross-entropy inspired antenna array diagnosis detection (CE-AAD) technique by exploiting the correlations of adjacent antennas, when blockages occur at the transmitter. Then, we extend the proposed CE-AAD algorithm to the case, where blockages occur at transmitter and receiver simultaneously. Our simulation results show that the proposed CE-AAD algorithm outperforms its traditional counterparts.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
