ترغب بنشر مسار تعليمي؟ اضغط هنا

Direct Numerical Simulation of Fluid Flow in a 5x5 Square Rod Bundle Using Nek5000

293   0   0.0 ( 0 )
 نشر من قبل Adam Kraus
 تاريخ النشر 2020
  مجال البحث فيزياء
والبحث باللغة English




اسأل ChatGPT حول البحث

Rod bundle flows are commonplace in nuclear engineering, and are present in light water reactors (LWRs) as well as other more advanced concepts. Inhomogeneities in the bundle cross section can lead to complex flow phenomena, including varying local conditions of turbulence. Despite the decades of numerical and experimental investigations regarding this topic, and the importance of elucidating the physics of the flow field, to date there are few publicly available direct numerical simulations (DNS) of the flow in multiple-pin rod bundles. Thus a multiple-pin DNS study can provide significant value toward reaching a deeper understanding of the flow physics, as well as a reference simulation for development of various reduced-resolution analysis techniques. To this end, DNS of the flow in a square 5x5 rod bundle at Reynolds number of 19,000 has been performed using the highly-parallel spectral element code Nek5000. The geometrical dimensions were representative of typical LWR fuel designs. The DNS was designed using microscales estimated from an advanced Reynolds-Averaged Navier-Stokes (RANS) model. Characteristics of the velocity field, Reynolds stresses, and anisotropy are presented in detail for various regions of the bundle. The turbulent kinetic energy budget is also presented and discussed



قيم البحث

اقرأ أيضاً

Rod bundle flows are prevalent in nuclear engineering for both light water reactors (LWR) and advanced reactor concepts. Unlike canonical channel flow, the flow in rod bundles presents some unique characteristics, notably due to the inhomogeneous cro ss section which can present different local conditions of turbulence as well as localized effects characteristic of external flows. Despite the ubiquity of rod bundle flows and the decades of experimental and numerical knowledge acquired in this field, there are no publicly available direct numerical simulations (DNS) of the flow in multiple pin rod bundles with heat transfer. A multiple pin DNS study is of great value as it would allow for assessment of the reliability of various turbulence models in the presence of heat transfer, as well as allow for a deeper understanding of the flow physics. We present work towards DNS of the flow in a square 5x5 rod bundle representative of LWR fuel. We consider standard configurations as well as configurations where the central pin is replaced with a guide thimble. We perform simulations in STAR-CCM+ to design the numerical DNS, which is to be conducted using the open source spectral element code Nek5000. Large Eddy Simulations are also performed in Nek5000 to confirm that the resolution requirements are adequate. We compare results from STAR-CCM+ and Nek5000, which show very good agreement in the wide gaps with larger discrepancies in the narrow gaps. In particular, evidence of a gap vortex street is seen in the edge subchannels in LES but is not predicted by STAR-CCM+.
A direct numerical simulation (DNS) of a channel flow with one curved surface was performed at moderate Reynolds number (Re_tau = 395 at the inlet). The adverse pressure gradient was obtained by a wall curvature through a mathematical mapping from ph ysical coordinates to Cartesian ones. The code, using spectral spanwise and normal discretization, combines the advantage of a good accuracy with a fast integration procedure compared to standard numerical procedures for complex geometries. The turbulent flow slightly separates on the profile at the lower curved wall and is at the onset of separation at the opposite flat wall. The thin separation bubble is characterized with a reversal flow fraction. Intense vortices are generated near the separation line on the lower wall but also at the upper wall. Turbulent normal stresses and kinetic energy budget are investigated along the channel.
Sand traps are used to measure Aeolian flux. Since they modify the surrounding wind velocity field their gauging represents an important challenge. We use numerical simulations under the assumption of homogeneous turbulence based on FLUENT to systema tically study the flow field and trapping efficiency of one of the most common devices based on a hollow cylinder with two slits. In particular, we investigate the dependence on the wind speed, the Stokes number, the permeability of the membrane on the slit and the saltation height.
The efficient mixing of fluids is key in many applications, such as chemical reactions and nanoparticle precipitation. Detailed experimental measurements of the mixing dynamics are however difficult to obtain, and so predictive numerical tools are he lpful in designing and optimizing many processes. If two different fluids are considered, the viscosity and density of the mixture depend often nonlinearly on the composition, which makes the modeling of the mixing process particularly challenging. Hence water-water mixtures in simple geometries such as T-mixers have been intensively investigated, but little is known about the dynamics of more complex mixtures, especially in the turbulent regime. We here present a numerical method allowing the accurate simulation of two-fluid mixtures. Using a high-performance implementation of this method we perform direct numerical simulations resolving the spatial and temporal dynamics of water-ethanol flows for Reynolds numbers from 100 to 2000. The flows states encountered during turbulence transition and their mixing properties are discussed in detail and compared to water-water mixtures.
The turbulent boundary layer over a flat plate is computed by direct numerical simulation (DNS) of the incompressible Navier-Stokes equations as a test bed for a synthetic turbulence generator (STG) inflow boundary condition. The inlet momentum thick ness Reynolds number is approximately 1,000. The study provides validation of the ability of the STG to develop accurate turbulence in 5 to 7 boundary layer thicknesses downstream of the boundary condition. Also tested was the effect of changes in the stabilization scheme on the development of the boundary layer. Moreover, the grid resolution required for both the development region and the downstream flow is investigated when using a stabilized finite element method.
التعليقات
جاري جلب التعليقات جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
mircosoft-partner

هل ترغب بارسال اشعارات عن اخر التحديثات في شمرا-اكاديميا