اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدTowards smooth (010) beta-Ga2O3 films homoepitaxially grown by plasma assisted molecular beam epitaxy: The impact of substrate offcut and metal-to-oxygen flux ratio
176
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
Smooth interfaces and surfaces are beneficial for most (opto)electronic devices based on thin films and their heterostructures. For example, smoother interfaces in (010) beta-Ga2O3/(AlxGa1-x)2O3 heterostructures, whose roughness is ruled by that of the Ga2O3 layer, can enable higher mobility 2DEGs by reducing interface roughness scattering. To this end we experimentally prove that a substrate offcut along the [001] direction allows to obtain smooth beta-Ga2O3 layers in (010)-homoepitaxy under metal-rich conditions. Applying In-mediated metal-exchange catalysis (MEXCAT) in molecular beam epitaxy at high substrate temperatures (Tg = 900 {deg}C) we compare the morphology of layers grown on (010)-oriented substrates with different unintentional offcuts. The layer roughness is generally ruled by (i) (110) and (-110)-facets visible as elongated features along the [001] direction (rms < 0.5 nm), and (ii) trenches (5-10 nm deep) orthogonal to [001]. We show that an unintentional substrate offcut of only 0.1{deg} almost oriented along the [001] direction suppresses these trenches resulting in a smooth morphology with a roughness exclusively determined by the facets, i.e., rms 0.2 nm. Since we found the facet-and-trench morphology in layers grown by MBE with and without MEXCAT, we propose that the general growth mechanism for (010)-homoepitaxy is ruled by island growth whose coalescence results in the formation of the trenches. The presence of a substrate offcut in the [001] direction can allow for step-flow growth or island nucleation at the step edges, which prevents the formation of trenches. Moreover, we give experimental evidence for a decreasing surface diffusion length or increasing nucleation density with decreasing metal-to-oxygen flux ratio. Based on our results we can rule-out step bunching as cause of the trench formation as well as a surfactant-effect of indium during MEXCAT.
قيم البحث
اقرأ أيضاً
We have investigated the growth of BaTiO3 thin films deposited on pure and 1% Nb-doped SrTiO3(001) single crystals using atomic oxygen assisted molecular beam epitaxy (AO-MBE) and dedicated Ba and Ti Knudsen cells. Thicknesses up to 30 nm were invest
igated for various layer compositions. We demonstrate 2D growth and epitaxial single crystalline BaTiO3 layers up to 10 nm before additional 3D features appear; lattice parameter relaxation occurs during the first few nanometers and is completed at {guillemotright}10 nm. The presence of a Ba oxide rich top layer that probably favors 2D growth is evidenced for well crystallized layers. We show that the Ba oxide rich top layer can be removed by chemical etching. The present work stresses the importance of stoichiometry and surface composition of BaTiO3 layers, especially in view of their integration in devices.
A range of high quality Ga1-xMnxN layers have been grown by molecular beam epitaxy with manganese concentration 0.2 < x < 10%, having the x value tuned by changing the growth temperature (Tg) between 700 and 590 {deg}C, respectively. We present a sys
tematic structural and microstructure characterization by atomic force microscopy, secondary ion mass spectrometry, transmission electron microscopy, powder-like and high resolution X-ray diffraction, which do not reveal any crystallographic phase separation, clusters or nanocrystals, even at the lowest Tg. Our synchrotron based X-ray absorption near-edge spectroscopy supported by density functional theory modelling and superconducting quantum interference device magnetometry results point to the predominantly +3 configuration of Mn in GaN and thus the ferromagnetic phase has been observed in layers with x > 5% at 3 < T < 10 K. The main detrimental effect of Tg reduced to 590 {deg}C is formation of flat hillocks, which increase the surface root-mean-square roughness, but only to mere 3.3 nm. Fine substrates surface temperature mapping has shown that the magnitudes of both x and Curie temperature (Tc) correlate with local Tg. It has been found that a typical 10 {deg}C variation of Tg across 1 inch substrate can lead to 40% dispersion of Tc. The established here strong sensitivity of Tc on Tg turns magnetic measurements into a very efficient tool providing additional information on local Tg, an indispensable piece of information for growth mastering of ternary compounds in which metal species differ in almost every aspect of their growth related parameters determining the kinetics of the growth. We also show that the precise determination of Tc by two different methods, each sensitive to different moments of Tc distribution, may serve as a tool for quantification of spin homogeneity within the material.
In this work we investigate the growth of $beta$-Ga2O3 homoepitaxial layers on top of (100) oriented substrates via indium-assisted metal exchange catalyzed molecular beam epitaxy (MEXCAT-MBE) which have exhibited prohibitively low growth rates by no
n-catalyzed MBE in the past. We demonstrate that the proper tuning of the MEXCAT growth parameters and the choice of a proper substrate offcut allow for the deposition of thin films with high structural quality via step-flow growth mechanism at relatively high growth rates for $beta$-Ga2O3 homoepitaxy (i.e., around 1.5 nm/min, $approx$45% incorporation of the incoming Ga flux), making MBE growth on this orientation feasible. Moreover, through the employment of the investigated four different (100) substrate offcuts along the [00-1] direction (i.e., 0$^circ$, 2$^circ$, 4$^circ$, 6$^circ$) we give experimental evidence on the fundamental role of the (-201) step edges as nucleation sites for growth of (100)-oriented Ga2O3 films by MBE.
A comprehensive current-voltage (I-V) characterization is performed for three different Schottky contacts; Pt, Ni and Ti, to unintentionally doped (UID) {beta}-(Al0.19Ga0.81)2O3 grown by molecular beam epitaxy (MBE) on {beta}-Ga2O3 for temperatures r
anging between 25C -300C. Reciprocal space mapping shows the (Al0.19Ga0.81)2O3 films are strained and lattice matched to the substrate. Schottky Barrier Height (SBH), ideality factor (n), and series resistance (Rs) are extracted from the I-V characteristics for the three types of metals and temperatures. Room temperature capacitance-voltage (C-V) measurements revealed fully depleted {beta}-(Al0.19Ga0.81)2O3 layer. Extracted room temperature SBHs after zero field correction for Pt, Ni and Ti were 2.39 eV, 2.21 eV, and 1.22 eV respectively. Variation of SBHs with metal clearly indicates the dependence on work function.
Atomically thin PtSe2 films have attracted extensive research interests for potential applications in high-speed electronics, spintronics and photodetectors. Obtaining high quality, single crystalline thin films with large size is critical. Here we r
eport the first successful layer-by-layer growth of high quality PtSe2 films by molecular beam epitaxy. Atomically thin films from 1 ML to 22 ML have been grown and characterized by low-energy electron diffraction, Raman spectroscopy and X-ray photoemission spectroscopy. Moreover, a systematic thickness dependent study of the electronic structure is revealed by angle-resolved photoemission spectroscopy (ARPES), and helical spin texture is revealed by spin-ARPES. Our work provides new opportunities for growing large size single crystalline films for investigating the physical properties and potential applications of PtSe2.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
