اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدAutomatic Mapping of the Indoor World with Personal Radars
99
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
Digital maps will revolutionize our experience of perceiving and navigating indoor environments. While today we rely only on the representation of the outdoors, the mapping of indoors is mainly a part of the traditional SLAM problem where robots discover the surrounding and perform self-localization. Nonetheless, robot deployment prevents from a large diffusion and fast mapping of indoors and, further, they are usually equipped with laser and vision technology that fail in scarce visibility conditions. To this end, a possible solution is to turn future personal devices into personal radars as a milestone towards the automatic generation of indoor maps using massive array technology at millimeter-waves, already in place for communications. In this application-oriented paper, we will describe the main achievements attained so far to develop the personal radar concept, using ad-hoc collected experimental data, and by discussing possible future directions of investigation.
قيم البحث
اقرأ أيضاً
Several schemes for gain control are used for preventing saturation of receiver, and overloading of data processor, tracker or display in pulse radars. The use of digital processing techniques open the door to a variety of digital automatic gain cont
rol schemes for analyzing digitized return signals and controlling receiver gain only at saturating clutter zones without affecting the detection at other zones. In this paper, we present a novel scheme of Digital Instantaneous Automatic Gain Control (DIAGC) which is based on storing digitally the dwell based clutter returns and deriving the gain control. The returns corresponding to the first two PRTs in a dwell are used to analyze the presence of saturating clutter zones and the depth of saturation. Third PRT onwards proper gain control is applied at the IF stage to prevent saturation of the following stages. FPGA based scheme is used for digital data processing, storing, threshold calculation and gain control generation. The effect of DIAGC on pulse compression is also addressed in this paper.
This paper presents the design, implementation and evaluation of milliMap, a single-chip millimetre wave (mmWave) radar based indoor mapping system targetted towards low-visibility environments to assist in emergency response. A unique feature of mil
liMap is that it only leverages a low-cost, off-the-shelf mmWave radar, but can reconstruct a dense grid map with accuracy comparable to lidar, as well as providing semantic annotations of objects on the map. milliMap makes two key technical contributions. First, it autonomously overcomes the sparsity and multi-path noise of mmWave signals by combining cross-modal supervision from a co-located lidar during training and the strong geometric priors of indoor spaces. Second, it takes the spectral response of mmWave reflections as features to robustly identify different types of objects e.g. doors, walls etc. Extensive experiments in different indoor environments show that milliMap can achieve a map reconstruction error less than 0.2m and classify key semantics with an accuracy around 90%, whilst operating through dense smoke.
Indoor wireless simultaneous localization and mapping (SLAM) is considered as a promising technique to provide positioning services in future 6G systems. However, the accuracy of traditional wireless SLAM system heavily relies on the quality of propa
gation paths, which is limited by the uncontrollable wireless environment. In this paper, we propose a novel SLAM system assisted by a reconfigurable intelligent surface (RIS) to address this issue. By configuring the phase shifts of the RIS, the strength of received signals can be enhanced to resist the disturbance of noise. However, the selection of phase shifts heavily influences the localization and mapping phase, which makes the design very challenging. To tackle this challenge, we formulate the RIS-assisted indoor SLAM optimization problem and design an error minimization algorithm for it. Simulations show that the RIS assisted SLAM system can decrease the positioning error by at least 31% compared with benchmark schemes.
This article develops the multiple-input multiple-output (MIMO) technology for weather radar sensing. There are ample advantages of MIMO that have been highlighted that can improve the spatial resolution of the observations and also the accuracy of t
he radar variables. These concepts have been introduced here pertaining to weather radar observations with supporting simulations demonstrating improvements to existing phased array technology. Already MIMO is being used in a big way for hard target detection and tracking and also in the automotive radar industry and it offers similar improvements for weather radar observations. Some of the benefits are discussed here with a phased array platform in mind which offers quadrant outputs.
In this paper, we describe the evolution of a pair of polyphase coded waveform for use in second trip suppression in weather radar. The polyphase codes were designed and tested on NASA weather radar. The NASA dual-frequency, dual-polarization Doppler
radar (D3R) was developed primarily as a ground validation tool for the GPM satellite dual-frequency radar. Recently, the D3R radar was upgraded with n
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
