اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدAn innovative, fast and facile soft-template approach for the fabrication of porous PDMS for oil-water separation
69
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
Oil wastewater and spilled oil caused serious environmental pollution and damage to public health in the last years. Therefore, considerable efforts are made to develop sorbent materials able to separate oil from water with high selectivity and sorption capacity. However most of them are low reusable, with low volume absorption capacity and poor mechanical properties. Moreover, the synthesis is time-consuming, complex and expensive limiting its practical application in case of emergency. Here we propose an innovative approach for the fabrication of porous PDMS starting from an inverse water-in-silicone procedure able to selectively collect oil from water in few seconds. The synthesis is dramatically faster than previous approaches, permitting the fabrication of the material in few minutes independently from the dimension of the sponges. The porous material evidenced a higher volume sorption capacity with respect to other materials already proposed for oil sorption from water and excellent mechanical and reusability properties.This innovative fast and simple approach can be successful in case of emergency, as oil spill accidents, permitting in situ fabrication of porous absorbents.
قيم البحث
اقرأ أيضاً
The formation of smart emulsions or foams whose stability can be controlled on-demand by switching external parameters is of great interest for basic research and applications. An emerging group of smart stabilizers are microgels, which are nano- and
micro-sized, three-dimensional polymer networks that are swollen by a good solvent. In the last decades, the influence of various external stimuli on the two-dimensional phase behavior of microgels at air- and oil-water interfaces has been studied. However, the impact of the top-phase itself has been barely considered. Here, we present data that directly address the influence of the top-phase on the microgel properties at interfaces. The dimensions of pNIPAM microgels are measured after deposition from two interfaces, i.e., air- and decane-water. While the total in-plane size of the microgel increases with increasing interfacial tension, the portions or fractions of the microgels situated in the aqueous phase are not affected. We correlate the area microgels occupy to the surface tensions of the interfaces, which allows to estimate an elastic modulus. In comparison to nanoindentation measurements, we observe a larger elastic modulus for the microgels. By combining compression, deposition, and visualization, we show that the two-dimensional phase behavior of the microgel monolayers is not altered, although the microgels have a larger total in-plane size at higher interfacial tension. A peer reviewed and extended version of this preprint and the electronic supplementary information can be found under S.~Bochenek, A.~Scotti, W.~Richtering, textit{Soft Matter}, 2020, DOI: 10.1039/d0sm01774d.
We report the successful synthesis of nanotubules of thermoelectric materials gamma-NaxCoO2 using two different sol-gel routes aided by porous anodized aluminium oxide (AAO) membrane as supporting templates. The gamma-NaxCoO2 nanotubule using urea-ba
sed route can be achieved at 650 degree C at a heating rate of 1 degree C/min and held for 4h. The gamma-NaxCoO2 nanotubule using citric acid-based route can be achieved at 500 degree C using a rapid-heat-up procedure and held for 30 min. The products were investigated using various techniques including XRD, SEM and TEM. Electron diffraction pattern taken along [001] zone axis direction on the nanotubule shows that all the diffraction spots can be indexed using a hexagonal unit cell with a = b = 0.56 nm, which can be considered as a superstructure with cell doubling within the ab plane.
A simple scalable scheme is reported for fabricating suspended carbon nanotube field effect transistors (CNT-FETs) without exposing pristine as-grown carbon nanotubes to subsequent chemical processing. Versatility and ease of the technique is demonst
rated by controlling the density of suspended nanotubes and reproducing devices multiple times on the same electrode set. Suspending the carbon nanotubes results in ambipolar transport behavior with negligible hysteresis. The Hooges constant of the suspended CNT-FETs (2.6 x 10-3) is about 20 times lower than for control CNT-FETs on SiO2 (5.6 x 10-2).
We report on a nanomechanical engineering method to monitor matter growth in real time via e-beam electromechanical coupling. This method relies on the exceptional mass sensing capabilities of nanomechanical resonators. Focused electron beam induced
deposition (FEBID) is employed to selectively grow platinum particles at the free end of singly clamped nanotube cantilevers. The electron beam has two functions: it allows both to grow material on the nanotube and to track in real time the deposited mass by probing the noise-driven mechanical resonance of the nanotube. On the one hand, this detection method is highly effective as it can resolve mass deposition with a resolution in the zeptogram range; on the other hand, this method is simple to use and readily available to a wide range of potential users, since it can be operated in existing commercial FEBID systems without making any modification. The presented method allows to engineer hybrid nanomechanical resonators with precisely tailored functionality. It also appears as a new tool for studying growth dynamics of ultra-thin nanostructures, opening new opportunities for investigating so far out-of-reach physics of FEBID and related methods.
Although, poly(dimethylsiloxane) (PDMS) is a widely used material in numerous applications, such as micro- or nanofabrication, the method of its selective etching has not been known up to now. In this work authors present two methods of etching the p
ure, additive-free and cured PDMS as a positive resist material. To achieve the chemical modification of the polymer necessary for selective etching, energetic ions were used. We created 7 um and 45 um thick PDMS layers and patterned them by a focused proton microbeam with various, relatively large fluences. In this paper authors demonstrate that 30 wt% Potassium Hydroxide (KOH) or 30 wt% sodium hydroxide (NaOH) at 70 oC temperature etch proton irradiated PDMS selectively, and remove the chemically sufficiently modified areas. In case of KOH development, the maximum etching rate was approximately 3.5 um/minute and it occurs at about 7.5*10^15 ion*cm-2. In case of NaOH etching the maximum etching rate is slightly lower, 1.75 um/minute and can be found at the slightly higher fluence of 8.75*10^15 ion*cm-2. These results are of high importance since up to this time it has not been known how to develop the additive-free, cross-linked poly(dimethylsiloxane) in lithography as a positive tone resist material.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
