اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدTool steel ion beam assisted nitrocarburization
80
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
The nitrocarburization of the AISI-H13 tool steel by ion beam assisted deposition is reported. In this technique, a carbon film is continuously deposited over the sample by the ion beam sputtering of a carbon target while a second ion source is used to bombard the sample with low energy nitrogen ions. The results show that the presence of carbon has an important impact on the crystalline and microstructural properties of the material without modification of the case depth.
قيم البحث
اقرأ أيضاً
A comprehensive study of pulsed nitriding in AISI H13 tool steel at low temperature (400{deg}C) is reported for several durations. X-ray diffraction results reveal that a nitrogen enriched compound (Epsilon-Fe2-3N, iron nitride) builds up on the surf
ace within the first process hour despite the low process temperature. Beneath the surface, X-ray Wavelength Dispersive Spectroscopy (WDS) in a Scanning Electron Microscope (SEM) indicates relatively higher nitrogen concentrations (up to 12 at.%) within the diffusion layer while microscopic nitrides are not formed and existing carbides are not dissolved. Moreover, in the diffusion layer, nitrogen is found to be dispersed in the matrix and forming nanosized precipitates. The small coherent precipitates are observed by High-Resolution Transmission Electron Microscopy (HR-TEM) while the presence of nitrogen is confirmed by electron energy loss spectroscopy (EELS). Hardness tests show that the material hardness increases linearly with the nitrogen concentration, reaching up to 14.5 GPa in the surface while the Young Modulus remains essentially unaffected. Indeed, the original steel microstructure is well preserved even in the nitrogen diffusion layer. Nitrogen profiles show a case depth of about ~43 microns after nine hours of nitriding process. These results indicate that pulsed plasma nitriding is highly efficient even at such low temperatures and that at this process temperature it is possible to form thick and hard nitrided layers with satisfactory mechanical properties. This process can be particularly interesting to enhance the surface hardness of tool steels without exposing the workpiece to high temperatures and altering its bulk microstructure.
The deposition of boron-doped amorphous carbon thin films on SiO2 substrate was achieved via a focused ion beam-assisted chemical vapor deposition of triphenyl borane (C18H15B) and triphenyl borate (C18H15BO3). The existence of boron in the deposited
film from triphenyl borane, with a precursor temperature of 90 {deg}C, was confirmed by a core level X-ray photoelectron spectroscopy analysis. The film exhibited a semiconducting behavior with a band gap of 285 meV. Although the band gap was decreased to 197 meV after an annealing process, the film was still semiconductor. Additionally, a drastic reduction of the resistance on the deposited film by applying pressures was observed from an in-situ electrical transport measurements using a diamond anvil cell.
In this paper we report the effect of hydrogen on the structural properties of AISI-H13 steel nitrogen-implanted samples in low oxygen partial pressure atmosphere. The samples were implanted in a high vacuum chamber by using a broad ion beam source.
The H2+/N2+ ion composition of the beam was varied and the surface composition studied in situ by photoemission electron spectroscopy (XPS). The samples were also ex situ analyzed by X-ray diffraction and scanning electron microscopy (SEM), including energy-dispersive spectroscopy measurements. It was found that hydrogen has the effect of modifying the amount of retained nitrogen at the surfaces. This result shows that hydrogen plays a role beyond the well-established effect of oxygen etching in industrial machines where vacuum is relatively less well controlled. Finally, an optimum concentration of 20 to 40% [H2]/[H2+N2] ion beam composition was determined to obtain maximum nitrogen incorporation on the metal surface.
Due to the mechanical and inertness properties of the Epsilon phase, its formation as a compact monolayer is most wanted in plasma surface treatments of steels. This phase can be obtained by the inclusion of carbon species in the plasma. In this work
, we present a systematic study of the carbon influence on the compound layer in an AISI H13 tool steel by pulsed plasma nitrocarburizing process with different gaseous ratios.
The impact of 400 keV $Ar^+$ ion irradiation on the magnetic and electrical properties of in-plane magnetized magnetic tunnel junction (MTJ) stacks was investigated by ferromagnetic resonance, vibrating sample magnetometry and current-in-plane tunnel
ing techniques. The irradiation-induced changes of the magnetic anisotropy, coupling energies and tunnel magnetoresistance (TMR) exhibited a correlated dependence on the ion fluence, which allowed us to distinguish between two irradiation regimes. In the low-fluence regime, ${Phi} < 10^{14} cm^{-2}$, the parameters required for having a functioning MTJ were preserved: the anisotropy of the FeCoB free layer (FL) was weakly modulated following a small decrease in the saturation magnetization $M_S$; the TMR decreased continuously; the interlayer exchange coupling (IEC) and the exchange bias (EB) decreased slightly. In the high-fluence regime, ${Phi} > 10^{14} cm^{-2}$, the MTJ was rendered inoperative: the modulation of the FL anisotropy was strong, caused by a strong decrease in $M_S$, ascribed to a high degree of interface intermixing between the FL and the Ta capping; the EB and IEC were also lost, likely due to intermixing of the layers composing the synthetic antiferromagnet; and the TMR vanished due to the irradiation-induced deterioration of the MgO barrier and MgO/FeCoB interfaces. We demonstrate that the layers surrounding the FL play a decisive role in determining the trend of the magnetic anisotropy evolution resulting from the irradiation, and that an ion-fluence window exists where such a modulation of magnetic anisotropy can occur, while not losing the TMR or the magnetic configuration of the MTJ.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
