اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدEffect of Carbon on the Compound Layer Properties of AISI H13 Tool Steel in Pulsed Plasma Nitrocarburizing
80
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
Due to the mechanical and inertness properties of the Epsilon phase, its formation as a compact monolayer is most wanted in plasma surface treatments of steels. This phase can be obtained by the inclusion of carbon species in the plasma. In this work, we present a systematic study of the carbon influence on the compound layer in an AISI H13 tool steel by pulsed plasma nitrocarburizing process with different gaseous ratios.
قيم البحث
اقرأ أيضاً
A comprehensive study of pulsed nitriding in AISI H13 tool steel at low temperature (400{deg}C) is reported for several durations. X-ray diffraction results reveal that a nitrogen enriched compound (Epsilon-Fe2-3N, iron nitride) builds up on the surf
ace within the first process hour despite the low process temperature. Beneath the surface, X-ray Wavelength Dispersive Spectroscopy (WDS) in a Scanning Electron Microscope (SEM) indicates relatively higher nitrogen concentrations (up to 12 at.%) within the diffusion layer while microscopic nitrides are not formed and existing carbides are not dissolved. Moreover, in the diffusion layer, nitrogen is found to be dispersed in the matrix and forming nanosized precipitates. The small coherent precipitates are observed by High-Resolution Transmission Electron Microscopy (HR-TEM) while the presence of nitrogen is confirmed by electron energy loss spectroscopy (EELS). Hardness tests show that the material hardness increases linearly with the nitrogen concentration, reaching up to 14.5 GPa in the surface while the Young Modulus remains essentially unaffected. Indeed, the original steel microstructure is well preserved even in the nitrogen diffusion layer. Nitrogen profiles show a case depth of about ~43 microns after nine hours of nitriding process. These results indicate that pulsed plasma nitriding is highly efficient even at such low temperatures and that at this process temperature it is possible to form thick and hard nitrided layers with satisfactory mechanical properties. This process can be particularly interesting to enhance the surface hardness of tool steels without exposing the workpiece to high temperatures and altering its bulk microstructure.
In this paper we report the effect of hydrogen on the structural properties of AISI-H13 steel nitrogen-implanted samples in low oxygen partial pressure atmosphere. The samples were implanted in a high vacuum chamber by using a broad ion beam source.
The H2+/N2+ ion composition of the beam was varied and the surface composition studied in situ by photoemission electron spectroscopy (XPS). The samples were also ex situ analyzed by X-ray diffraction and scanning electron microscopy (SEM), including energy-dispersive spectroscopy measurements. It was found that hydrogen has the effect of modifying the amount of retained nitrogen at the surfaces. This result shows that hydrogen plays a role beyond the well-established effect of oxygen etching in industrial machines where vacuum is relatively less well controlled. Finally, an optimum concentration of 20 to 40% [H2]/[H2+N2] ion beam composition was determined to obtain maximum nitrogen incorporation on the metal surface.
The modification of steel (AISI 316L and AISI 4140) surface morphology and underlying inter-crystalline grains strain due to Xe$^+$ ion bombardment are reported to affect nitrogen diffusion after a pulsed plasma nitriding process. The ion bombardment
induces regular nanometric patterns and increases the roughness of the material surface. The strain induced by the noble gas bombardment is observed in depths which are orders of magnitude larger than the projectiles stopping distance. The pre-bombarded samples show peculiar microstructures formed in the nitrided layers, modifying the in-depth hardness profile. Unlike the double nitrided layer normally obtained in austenitic stainless steel by pulsed plasma nitriding process, the Xe$^+$ pre-bombardment treatment leads to a single thick compact layer. In nitrided pre-bombarded AISI 4140 steel, the diffusion zone shows long iron nitride needle-shaped precipitates, while in non-pre-bombarded samples finer precipitates are distributed in the material.
Plastic flow behavior of low carbon steel has been studied at room temperature during tensile deformation by varying the initial strain rate of 3.3x10e-4 1/sec to the final strain rate ranging from 1.33x10e-3 1/sec to 2.0x10e-3 1/sec at a fixed engin
eering strain of 12%. Haasen plot revealed that the mobile dislocation density remained almost invariant at the juncture where there was a sudden increase in stress with the change in strain rate and the plastic flow was solely dependent on the velocity of mobile dislocations. In that critical regime, the variation of stress with time was fitted with a Boltzman type Sigmoid function. The increase in stress was found to increase with final strain rate and the time elapsed to attain these stress values showed a decreasing trend. Both of these parameters saturated asymptotically at higher final strain rate.
Since Reactor Pressure Vessel steels are ferromagnetic, they provide a convenient means to monitor changes in the mechanical properties of the material upon irradiation with high energy particles, by measuring their magnetic properties. Here, we disc
uss the correlation between these two properties (i.e. mechanical and magnetic properties) and microstructure, by studying the flux effect on the nuclear pressure vessel steel used in reactors currently under construction in Argentina. Charpy-V notched specimens of this steel were irradiated in the RA1 experimental reactor at 275{deg}C with two lead factors (LFs), 93 and 183. The magnetic properties were studied by means of DC magnetometry and ferromagnetic resonance. The results show that the coercive field and magnetic anisotropy spatial distribution are sensitive to the LF and can be explained by taking into account the evolution of the microstructure with this parameter. The saturation magnetization shows a dominant dependence on the accumulated damage. Consequently, the mentioned techniques are suitable to estimate the degradation of the reactor vessel steel.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
