اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدThermoelectric bolometers based on ultra-thin heavily doped single-crystal silicon membranes
65
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
We present ultra-thin silicon membrane thermocouple bolometers suitable for fast and sensitive detection of low levels of thermal power and infrared radiation at room temperature. The devices are based on 40 nm-thick strain tuned single crystalline silicon membranes shaped into heater/absorber area and narrow n- and p-doped beams, which operate as the thermocouple. The electro-thermal characterization of the devices reveal noise equivalent power of 13 pW/rtHz and thermal time constant of 2.5 ms. The high sensitivity of the devices is due to the high Seebeck coefficient of 0.39 mV/K and reduction of thermal conductivity of the Si beams from the bulk value. The bolometers operate in the Johnson-Nyquist noise limit of the thermocouple, and the performance improvement towards the operation close to the temperature fluctuation limit is discussed.
قيم البحث
اقرأ أيضاً
We report on fabrication and characterization of ultra-thin suspended single crystalline flat silicon membranes with thickness down to 6 nm. We have developed a method to control the strain in the membranes by adding a strain compensating frame on th
e silicon membrane perimeter to avoid buckling of the released membranes. We show that by changing the properties of the frame the strain of the membrane can be tuned in controlled manner. Consequently, both the mechanical properties and the band structure can be engineered and the resulting membranes provide a unique laboratory to study low-dimensional electronic, photonic and phononic phenomena.
Superconductor films on semiconductor substrates draw much attention recently since the derived superconductor-based electronics have been shown promising for future data process and storage technologies. By growing atomically uniform single-crystal
epitaxial Pb films of several nanometers thick on Si wafers to form a sharp superconductor-semiconductor heterojunction, we have obtained an unusual giant magnetoresistance effect when the Pb film is superconducting. In addition to the great fundamental interest of this effect, the simple structure and compatibility and scalability with current Si-based semiconductor technology offer a great opportunity for integrating superconducting circuits and detectors in a single chip.
Understanding new superconductors requires high-quality epitaxial thin films to explore intrinsic electromagnetic properties, control grain boundaries and strain effects, and evaluate device applications. So far superconducting properties of ferropni
ctide thin films appear compromised by imperfect epitaxial growth and poor connectivity of the superconducting phase. Here we report novel template engineering using single-crystal intermediate layers of (001) SrTiO3 and BaTiO3 grown on various perovskite substrates that enables genuine epitaxial films of Co-doped BaFe2As2 with high transition temperature (zero resistivity Tc of 21.5K), small transition widths (delta Tc = 1.3K), superior Jc of 4.5 MA/cm2 (4.2K, self field) and strong c-axis flux pinning. Implementing SrTiO3 or BaTiO3 templates to match the alkaline earth layer in the Ba-122 with the alkaline earth-oxygen layer in the templates opens new avenues for epitaxial growth of ferropnictides on multi-functional single crystal substrates. Beyond superconductors, it provides a framework for growing heteroepitaxial intermetallic compounds on various substrates by matching interfacial layers between templates and thin film overlayers.
As mechanical structures enter the nanoscale regime, the influence of van der Waals forces increases. Graphene is attractive for nanomechanical systems because its Youngs modulus and strength are both intrinsically high, but the mechanical behavior o
f graphene is also strongly influenced by the van der Waals force. For example, this force clamps graphene samples to substrates, and also holds together the individual graphene sheets in multilayer samples. Here we use a pressurized blister test to directly measure the adhesion energy of graphene sheets with a silicon oxide substrate. We find an adhesion energy of 0.45 pm 0.02 J/m2 for monolayer graphene and 0.31 pm 0.03 J/m2 for samples containing 2-5 graphene sheets. These values are larger than the adhesion energies measured in typical micromechanical structures and are comparable to solid/liquid adhesion energies. We attribute this to the extreme flexibility of graphene, which allows it to conform to the topography of even the smoothest substrates, thus making its interaction with the substrate more liquid-like than solid-like.
Single crystal, nanoscale diamond membranes are highly sought after for a variety of applications including nanophotonics, nanoelectronics and quantum information science. However, so far, the availability of conductive diamond membranes remained an
unreachable goal. In this work we present a complete nanofabrication methodology for engineering high aspect ratio, electrically active single crystal diamond membranes. The membranes have large lateral directions, exceeding 500x500 um2 and are only several hundreds of nanometers thick. We further realize vertical single crystal p-n junctions, made from the diamond membranes that exhibit onset voltages of ~ 10V and a current of several mA. Moreover, we deterministically introduce optically active color centers into the membranes, and demonstrate for the first time a single crystal nanoscale diamond LED. The robust and scalable approach to engineer the electrically active single crystal diamond membranes, offers new pathways for advanced nanophotonics, nanoelectronics and optomechanics devices employing diamond.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
