اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدElectronic structure and photoluminescence properties of Zn-ion implanted silica glass before and after thermal annealing
64
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
The results of XPS core-level and valence band measurements, photoluminescence spectra of a-SiO2 implanted by Zn-ions (E=30 keV, D=1*1017 cm^-2) and Density Functional Theory calculations of electronic structure as well as formation energies of structural defects in silica glass induced by Zn-ion implantation are presented. Both theory and experiment show that it is energetically more favorable for implanted zinc ions to occupy the interstitial positions instead of cation substitution. As a result, the Zn-ions embedded to interstitials, form chemical bonds with the surrounding oxygen atoms, formation ZnO-like nanoparticles and oxygen-deficient SiOx matrix. The subsequent thermal annealing at 900 0C (1 hr) strongly reduces the amount of ZnO nanoparticles and induces the formation of {alpha}-Zn2SiO4 phase which markedly enhances the green emission.
قيم البحث
اقرأ أيضاً
Due to their outstanding mechanical properties, diamond and diamond-like materials find significant technological applications ranging from well-established industrial fields (cutting tools, coatings, etc.) to more advanced mechanical devices as micr
o- and nano-electromechanical systems. The use of energetic ions is a powerful and versatile tool to fabricate three-dimensional micro-mechanical structures. In this context, it is of paramount importance to have an accurate knowledge of the effects of ion-induced structural damage on the mechanical properties of this material, firstly to predict potential undesired side-effects of the ion implantation process, and possibly to tailor the desired mechanical properties of the fabricated devices. We present an Atomic Force Microscopy (AFM) characterization of free-standing cantilevers in single-crystal diamond obtained by a FIB-assisted lift-off technique, which allows a determination of the Youngs modulus of the diamond crystal after the MeV ion irradiation process concurrent to the fabrication of the microstructures, and subsequent thermal annealing. The AFM measurements were performed with the beam-bending technique and show that the thermal annealing process allows for an effective recovery of the mechanical properties of the pristine crystal.
Erbium doped low symmetry Y$_2$SiO$_5$ crystals attract a lot of attention in perspective of quantum information applications. However, only doping of the samples during growth is available up to now, which yields a quite homogeneous doping density.
In the present work, we deposit Er$^{3+}$-ions by the focused ion beam technique at Yttrium sites with several fluences in one sample. With a photoluminescence study of these locally doped Er$^{3+}$:Y$_2$SiO$_5$ crystals, we are able to evaluate the efficiency of the implantation process and develop it for the highest efficiency possible. We observe the dependence of the ion activation after the post-implantation annealing on the fluence value.
The surface properties of metallic implants play an important role in their clinical success. Improving upon the inherent shortcomings of Ti implants, such as poor bioactivity, is imperative for achieving clinical use. In this study, we have develope
d a Ti implant modified with Ca or dual Ca + Si ions on the surface using an electron cyclotron resonance ion source (ECRIS). The physicochemical and biological properties of ion-implanted Ti surfaces were analyzed using various analytical techniques, such as surface analyses, potentiodynamic polarization and cell culture. Experimental results indicated that a rough morphology was observed on the Ti substrate surface modified by ECRIS plasma ions. The in vitro electrochemical measurement results also indicated that the Ca + Si ion-implanted surface had a more beneficial and desired behavior than the pristine Ti substrate. Compared to the pristine Ti substrate, all ion-implanted samples had a lower hemolysis ratio. MG63 cells cultured on the high Ca and dual Ca + Si ion-implanted surfaces revealed significantly greater cell viability in comparison to the pristine Ti substrate. In conclusion, surface modification by electron cyclotron resonance Ca and Si ion sources could be an effective method for Ti implants.
The effect of substituting iron and zinc for cobalt in CaBaCo$_4$O$_7$ has been investigated using neutron diffraction and x-ray absorption spectroscopy. The orthorhombic distortion present in the parent compound CaBaCo$_4$O$_7$ decreases with increa
sing the content of either Fe or Zn. The samples CaBaCo$_3$ZnO$_7$ and CaBaCo$_{4-x}$Fe$_x$O$_7$ with $x leq 1.5$ are metrically hexagonal but much better refinements in the neutron diffraction patterns are obtained using an orthorhombic unit cell. The two types of substitution have opposite effects on the structural and magnetic properties. Fe atoms preferentially occupy the sites at the triangular layer. Thus, the replacement of Co by Fe supresses the ferrimagnetic ordering and CaBaCo$_{4-x}$Fe$_x$O$_7$ samples are antiferromagnetically ordered with a new propagation vector k=(1/3,0,0). However, the Zn atoms prefer occupying the Kagome layer, which is very detrimental for the long range magnetic interactions giving rise to a magnetic glass. The oxidation state of iron and zinc is found to be 3+ and 2+, respectively, independently of the content. Therefore, the average Co oxidation state changes accordingly with the Fe$^{3+}$ or Zn$^{2+}$ doping. Also, x-ray absorption spectroscopy data confirms the different preferential occupation for both Fe and Zn cations. The combined information obtained by neutron diffraction and x-ray absorption spectroscopy indicates that cobalt atoms can be either in a fluctuating Co$^{2+}$/Co$^{3+}$ valence state or, alternatively, Co$^{2+}$ and Co$^{3+}$ ions being randomly distributed in the lattice. These results explain the occurrence of local disorder in the CoO$_4$ tetrahedra obtained by EXAFS. An anomaly in the lattice parameters and an increase in the local disorder is observed only at the ferrimagnetic transition for CaBaCo$_4$O$_7$ revealing the occurrence of local magneto-elastic coupling.
Knowledge of mechanical and physical property evolution due to irradiation damage is essential for the development of future fission and fusion reactors. Ion-irradiation provides an excellent proxy for studying irradiation damage, allowing high damag
e doses without sample activation. Limited ion-penetration-depth means that only few-micron-thick damaged layers are produced. Substantial effort has been devoted to probing the mechanical properties of these thin implanted layers. Yet, whilst key to reactor design, their thermal transport properties remain largely unexplored due to a lack of suitable measurement techniques. Here we demonstrate non-contact thermal diffusivity measurements in ion-implanted tungsten for nuclear fusion armour. Alloying with transmutation elements and the interaction of retained gas with implantation-induced defects both lead to dramatic reductions in thermal diffusivity. These changes are well captured by our modelling approaches. Our observations have important implications for the design of future fusion power plants.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
