اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدThermodynamics deposition on curve nanoholes
109
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
In this work the thermodynamics of the electrodeposition on nanoholes is analyzed. Different lattice-gas models of nanoholes, from parallelepiped geometry to the empty bulk of a nanoparticle, were considered. The models include curvature on the inner walls. Several stages of deposition are identified. Monte Carlo technique in the Grand Canonical Ensemble is used to determine isotherms, isosteric heat, energy per site, etc. The study is based on different ranges of energies and nanoholes sizes.
قيم البحث
اقرأ أيضاً
Here we optimized the electrophoretic deposition process for the fabrication of WS2 plasmonic nanohole integrated structures. We showed how the conditions used for the site selective deposition influenced the properties of the deposited flakes. In pa
rticular, we investigated the effect of different suspension medium used during the deposition both in the efficiency of the process and in the stability of WS2 flakes, which were deposited on a ordered arrays of plasmonic nanostructures.
In this paper, a method is presented to create and characterize mechanically robust, free standing, ultrathin, oxide films with controlled, nanometer-scale thickness using Atomic Layer Deposition (ALD) on graphene. Aluminum oxide films were deposited
onto suspended graphene membranes using ALD. Subsequent etching of the graphene left pure aluminum oxide films only a few atoms in thickness. A pressurized blister test was used to determine that these ultrathin films have a Youngs modulus of 154 pm 13 GPa. This Youngs modulus is comparable to much thicker alumina ALD films. This behavior indicates that these ultrathin two-dimensional films have excellent mechanical integrity. The films are also impermeable to standard gases suggesting they are pinhole-free. These continuous ultrathin films are expected to enable new applications in fields such as thin film coatings, membranes and flexible electronics.
Despite the prevalence of sputter deposition in the microelectronics industry, it has seen very limited applications for graphene electronics. In this letter, we report systematic investigation of the sputtering induced damages in graphene and identi
fy the energetic sputtering gas neutrals as the primary cause of graphene disorder. We further demonstrate a grazing-incidence sputtering configuration that strongly suppresses fast neutral bombardment and retains graphene structure integrity, creating considerably lower damage than electron-beam evaporation. Such sputtering technique yields fully covered, smooth thin dielectric films, highlighting its potential for contact metals, gate oxides, and tunnel barriers fabrication in graphene device applications.
Chemically synthesized cove-type graphene nanoribbons (cGNRs) of different widths were brought into dispersion and drop-cast onto exfoliated hexagonal boron nitride (hBN) on a Si/SiO2 chip. With AFM we observed that the cGNRs form ordered domains ali
gned along the crystallographic axes of the hBN. Using electron beam lithography and metallization, we contacted the cGNRs with NiCr/Au, or Pd contacts and measured their I-V-characteristics. The transport through the ribbons was dominated by the Schottky behavior of the contacts between the metal and the ribbon.
In this note, we reply to the comment made by E.I.Kats and V.V.Lebedev [arXiv:1407.4298] on our recent work Thermodynamics of quantum crystalline membranes [Phys. Rev. B 89, 224307 (2014)]. Kats and Lebedev question the validity of the calculation pr
esented in our work, in particular on the use of a Debye momentum as a ultra-violet regulator for the theory. We address and counter argue the criticisms made by Kats and Lebedev to our work.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
