Subscribe to the gold package and get unlimited access to Shamra Academy
Register a new userField-Induced Resistive Switching in Metal-Oxide Interfaces
119
0
0.0
(
0
)
Authors
S. Tsui
Ask ChatGPT about the research
No Arabic abstract
We investigate the polarity-dependent field-induced resistive switching phenomenon driven by electric pulses in perovskite oxides. Our data show that the switching is a common occurrence restricted to an interfacial layer between a deposited metal electrode and the oxide. We determine through impedance spectroscopy that the interfacial layer is no thicker than 10 nm and that the switch is accompanied by a small capacitance increase associated with charge accumulation. Based on interfacial I-V characterization and measurement of the temperature dependence of the resistance, we propose that a field-created crystalline defect mechanism, which is controllable for devices, drives the switch.
rate research
Read More
We study the resistive switching (RS) mechanism as way to obtain multi-level memory cell (MLC) devices. In a MLC more than one bit of information can be stored in each cell. Here we identify one of the main conceptual difficulties that prevented the implementation of RS-based MLCs. We present a method to overcome these difficulties and to implement a 6-bit MLC device with a manganite-based RS device. This is done by precisely setting the remnant resistance of the RS-device to an arbitrary value. Our MLC system demonstrates that transition metal oxide non-volatile memories may compete with the currently available MLCs.
Films produced by assembling bare gold clusters well beyond the electrical percolation threshold show a resistive switching behavior whose investigation has started only recently. Here we address the challenge to charaterize the resistance of a nanogranular film starting from limited information on the structure at the microscopic scale by the means of Bruggemans approach to multicomponent media, within the framework of Effective Medium Approximations. The approach is used to build a model that proves that the observed resistive switching can be explained by thermally regulated local structural rearrangements.
The increasing demand for high-density data storage leads to an increasing interest in novel memory concepts with high scalability and the opportunity of storing multiple bits in one cell. A promising candidate is the redox-based resistive switch repositing the information in form of different resistance states. For reliable programming, the underlying physical parameters need to be understood. We reveal that the programmable resistance states are linked to internal series resistances and the fundamental nonlinear switching kinetics. The switching kinetics of Ta$_{2}$O$_{5}$-based cells was investigated in a wide range over 15 orders of magnitude from 250 ps to 10$^{5}$ s. We found strong evidence for a switching speed of 10 ps which is consistent with analog electronic circuit simulations. On all time scales, multi-bit data storage capabilities were demonstrated. The elucidated link between fundamental material properties and multi-bit data storage paves the way for designing resistive switches for memory and neuromorphic applications.
The polarity-dependent resistive-switching across metal-Pr0.7Ca0.3MnO3 interfaces is investigated. The data suggest that shallow defects in the interface dominate the switching. Their density and fluctuation, therefore, will ultimately limit the device size. While the defects generated/annihilated by the pulses and the associated carrier depletion seem to play the major role at lower defect density, the defect correlations and their associated hopping ranges appear to dominate at higher defect density. Therefore, the switching characteristics, especially the size-scalability, may be altered through interface treatments.
We report the observation of low-frequency modes in the Raman spectra of thin-film superlattices of the high-temperature superconductor YBa$ _{2} $Cu$ _{3} $O$ _{7-delta} $ and various manganite perovskites. Our study shows that these modes are caused by the backfolding of acoustic phonons due to the additional periodicity introduced by the superlattice. Such modes were previously only observed for ultra-pure semiconductor superlattices. They can be used to determine the bilayer thickness of the superlattice and its speed of sound. Moreover, we use the spatial resolution of Raman microscopy to map the film thickness inhomogeneity across a sample, making these modes a useful tool to characterize thin-film superlattices.
Log in to be able to interact and post comments
comments
Fetching comments
Sign in to be able to follow your search criteria
