Subscribe to the gold package and get unlimited access to Shamra Academy
Register a new userMonte Carlo Radiation Transport Modelling of the Current-Biased Kinetic Inductance Detector
95
0
0.0
(
0
)
Ask ChatGPT about the research
No Arabic abstract
Radiation transport simulations were used to analyse neutron imaging with the current-biased kinetic inductance detector (CB-KID). The PHITS Monte Carlo code was applied for simulating neutron, $^{4}$He, $^{7}$Li, photon and electron transport, $^{10}$B(n,$alpha$)$^{7}$Li reactions, and energy deposition by particles within CB-KID. Slight blurring in simulated CB-KID images originated $^{4}$He and $^{7}$Li ions spreading out in random directions from the $^{10}$B conversion layer in the detector prior to causing signals in the $X$ and $Y$ superconducting Nb nanowire meander lines. 478 keV prompt gamma rays emitted by $^{7}$Li nuclei from neutron-$^{10}$B reactions had negligible contribution to the simulated CB-KID images. Simulated neutron images of $^{10}$B dot arrays indicate that sub 10 $mu$m resolution imaging should be feasible with the current CB-KID design. The effect of the geometrical structure of CB-KID on the intrinsic detection efficiency was calculated from the simulations. An analytical equation was then developed to approximate this contribution to the detection efficiency. Detection efficiencies calculated in this study are upper bounds for the reality as the effects of detector temperature, the bias current, signal processing and dead-time losses were not taken into account. The modelling strategies employed in this study could be used to evaluate modifications to the CB-KID design prior to actual fabrication and testing, conveying a time and cost saving.
rate research
Read More
We have fabricated an array of subgap kinetic inductance detectors (SKIDs) made of granular aluminum ($T_csim$2~K) sensitive in the 80-90 GHz frequency band and operating at 300~mK. We measure a noise equivalent power of $1.3times10^{-16}$~W/Hz$^{0.5}$ on average and $2.6times10^{-17}$~W/Hz$^{0.5}$ at best, for an illuminating power of 50~fW per pixel. Even though the circuit design of SKIDs is identical to that of the kinetic inductance detectors (KIDs), the SKIDs operating principle is based on their sensitivity to subgap excitations. This detection scheme is advantageous because it avoids having to lower the operating temperature proportionally to the lowest detectable frequency. The SKIDs presented here are intrinsically selecting the 80-90 GHz frequency band, well below the superconducting spectral gap of the film, at approximately 180 GHz.
We describe the Monte Carlo (MC) simulation package of the Borexino detector and discuss the agreement of its output with data. The Borexino MC ab initio simulates the energy loss of particles in all detector components and generates the resulting scintillation photons and their propagation within the liquid scintillator volume. The simulation accounts for absorption, reemission, and scattering of the optical photons and tracks them until they either are absorbed or reach the photocathode of one of the photomultiplier tubes. Photon detection is followed by a comprehensive simulation of the readout electronics response. The algorithm proceeds with a detailed simulation of the electronics chain. The MC is tuned using data collected with radioactive calibration sources deployed inside and around the scintillator volume. The simulation reproduces the energy response of the detector, its uniformity within the fiducial scintillator volume relevant to neutrino physics, and the time distribution of detected photons to better than 1% between 100 keV and several MeV. The techniques developed to simulate the Borexino detector and their level of refinement are of possible interest to the neutrino community, especially for current and future large-volume liquid scintillator experiments such as Kamland-Zen, SNO+, and Juno.
We present a cryogenic wafer mapper based on light emitting diodes (LEDs) for spatial mapping of a large microwave kinetic inductance detector (MKID) array. In this scheme, an array of LEDs, addressed by DC wires and collimated through horns onto the detectors, is mounted in front of the detector wafer. By illuminating each LED individually and sweeping the frequency response of all the resonators, we can unambiguously correspond a detector pixel to its measured resonance frequency. We have demonstrated mapping a 76.2 mm 90-pixel MKID array using a mapper containing 126 LEDs with 16 DC bias wires. With the frequency to pixel-position correspondence data obtained by the LED mapper, we have found a radially position-dependent frequency non-uniformity < 1.6% over the 76.2 mm wafer. Our LED wafer mapper has no moving parts and is easy to implement. It may find broad applications in superconducting detector and quantum computing/information experiments.
An antihydrogen detector consisting of a thin BGO disk and a surrounding plastic scintillator hodoscope has been developed. We have characterized the two-dimensional positions sensitivity of the thin BGO disk and energy deposition into the BGO was calibrated using cosmic rays by comparing experimental data with Monte-Carlo simulations. The particle tracks were defined by connecting BGO hit positions and hits on the surrounding hodoscope scintillator bars. The event rate was investigated as a function of the angles between the tracks and the energy deposition in the BGO for simulated antiproton events, and for measured and simulated cosmic ray events. Identification of the antihydrogen Monte Carlo events was performed using the energy deposited in the BGO and the particle tracks. The cosmic ray background was limited to 12 mHz with a detection efficiency of 81 %. The signal-to-noise ratio was improved from 0.22 s^{-1/2} obtained with the detector in 2012 to 0.26 s^{-1/2} in this work.
We describe the fabrication of homogeneous sub-stoichiometric titanium nitride films for microwave kinetic inductance detector (mKID) arrays. Using a 6 inch sputtering target and a homogeneous nitrogen inlet, the variation of the critical temperature over a 2 inch wafer was reduced to <25 %. Measurements of a 132-pixel mKID array from these films reveal a sensitivity of 16 kHz/pW in the 100 GHz band, comparable to the best aluminium mKIDs. We measured a noise equivalent power of NEP = 3.6e-15 W/Hz^(1/2). Finally, we describe possible routes to further improve the performance of these TiN mKID arrays.
Log in to be able to interact and post comments
comments
Fetching comments
Sign in to be able to follow your search criteria
