Subscribe to the gold package and get unlimited access to Shamra Academy
Register a new userA statistical analysis of pores and micro-cracks in nuclear graphite
110
0
0.0
(
0
)
Ask ChatGPT about the research
No Arabic abstract
Microstructure characterization is of great value to understanding nuclear graphites properties and irradiation behavior. However, graphite is soft and could be easily damaged during sample preparation. A three-step polishing method involving mechanical polishing, ion milling and rapid oxidation is proposed for graphite. Ion milling is adopted to remove the broken graphite pieces produced by mechanical polishing. Rapid oxidation is then adopted to remove irradiation-induced damage layer during ion milling. The Raman spectra show very low G peak width and ID/IG ratio after rapid oxidation, indicating a surface completely free from artificial defects. The micro-cracks which were conventionally observed via a transmission electron microscope can be observed on rapid-oxidized surface in a scanning electron microscope. By digital image processing, the micro-cracks along with the gas-escape pores in nuclear graphite IG-110 are statistically analyzed. Porositys distributions on crack (pore) size (spanning from 10 nm to 100 um) are given, which could help to understand and simulate graphites performances in reactors.
rate research
Read More
To evaluate the stress level and damage of a reinforced concrete containment wall and its reaction to pressure variations, we implemented successive ultrasonic experiments on the exterior surface of the containment wall in the gusset area for three consecutive years. During each experiment, the pressure inside the containment wall increased gradually from 0 MPa to 0.43 MPa and then decreased back to 0 Mpa.From the analysis of the ultrasonic coda waves obtained in the multiple scattering regime, we performed Coda Wave Interferometry to calculate the apparent velocity changes in the structure (denoted by $dV/V_a$) and Coda Wave Decorrelation (DC) measurements to produce 3D cartographies of stress and crack distribution. From three source-receiver pairs, located at the top, middle and bottom of the experimental region, we observe that coda waves dilate, shrink and remain almost unchanged, respectively. This corresponds to the decreasing, increasing and invariant pressure inside the concrete. The comparison of three years results demonstrates that the variation of $dV/V_a$ and DC under the same pressure test increases through the years, which indicates the progressive deterioration and aging of the concrete. From a large collection of source-receiver pairs at different times, the spatial-temporal variations of $dV/V_a$ and DC are then used to produce a map of the structural velocity and scattering changes, respectively. We observe a decreasing velocity on the top part and an increasing in the middle one, which is in line with the $dV/V_a$ analysis. The reconstructed scattering changes (or structural changes) highlight the active region during the inflation-deflation procedure, corresponding to the opening and closing (and sometimes the development) of cracks. The larger magnitude in 2019 than in 2017 indicates the increasing damage in the concrete.
Recently, magnetic order in highly oriented pyrolytic graphite (HOPG) induced by proton broad- and microbeam irradiation was discovered. Theoretical models propose that hydrogen could play a major role in the magnetism mechanism. We analysed the hydrogen distribution of pristine as well as irradiated HOPG samples, which were implanted to micrometer-sized spots as well as extended areas with various doses of 2.25 MeV protons at the Leipzig microprobe LIPSION. For this we used the sensitive 3D hydrogen microscopy system at the Munich microprobe SNAKE. The background hydrogen level in pristine HOPG is determined to be less than 0.3 at-ppm. About 4.8e15 H-atoms/cm^2 are observed in the near-surface region (4 um depth resolution). The depth profiles of the implants show hydrogen located within a confined peak at the end of range, in agreement with SRIM Monte Carlo simulations, and no evidence of diffusion broadening along the c-axis. At sample with microspots, up to 40 at-% of the implanted hydrogen is not detected, providing support for lateral hydrogen diffusion.
Fluids in porous media are commonly studied with analytical or simulation methods, usually assuming that the host medium is rigid. By evaluating the substrates response (relaxation) to the presence of the fluid we assess the error inherent in that assumption. One application is a determination of the ground state of 3He in slit and cylindrical pores. With the relaxation, there results a much stronger cohesion than would be found for a rigid host. Similar increased binding effects of relaxation are found for classical fluids confined within slit pores or nanotube bundles.
We investigate the roughening of shear cracks running along the interface between a thin film and a rigid substrate. We demonstrate that short-range correlated fluctuations of the interface strength lead to self-affine roughening of the crack front as the driving force (the applied shear stress/stress intensity factor) increases towards a critical value. We investigate the disorder-induced perturbations of the crack displacement field and crack energy, and use the results to determine the crack pinning force and to assess the shape of the critical crack. The analytical arguments are validated by comparison with simulations of interface cracking.
Having smaller energy density than batteries, supercapacitors have exceptional power density and cyclability. Their energy density can be increased using ionic liquids and electrodes with sub-nanometer pores, but this tends to reduce their power density and compromise the key advantage of supercapacitors. To help address this issue through material optimization, here we unravel the mechanisms of charging sub-nanometer pores with ionic liquids using molecular simulations, navigated by a phenomenological model. We show that charging of ionophilic pores is a diffusive process, often accompanied by overfilling followed by de-filling. In sharp contrast to conventional expectations, charging is fast because ion diffusion during charging can be an order of magnitude faster than in bulk, and charging itself is accelerated by the onset of collective modes. Further acceleration can be achieved using ionophobic pores by eliminating overfilling/de-filling and thus leading to charging behavior qualitatively different from that in conventional, ionophilic pores.
Log in to be able to interact and post comments
comments
Fetching comments
Sign in to be able to follow your search criteria
