Subscribe to the gold package and get unlimited access to Shamra Academy
Register a new userInkjet Printed 2D-Crystal Based Strain Gauges on Paper
106
0
0.0
(
0
)
Ask ChatGPT about the research
No Arabic abstract
We present an investigation of inkjet printed strain gauges based on two-dimensional (2D) materials. The technology leverages water-based and biocompatible inks to fabricate strain measurement devices on flexible substrates such as paper. We demonstrate that the device performance and sensitivity are strongly dependent on the printing parameter (i.e., drop- spacing, number of printing passes, etc.). We show that values of the Gauge Factor up to 125 can be obtained, with large sensitivity (>20%) even when small strains (0.3%) are applied. Furthermore, we provide preliminary examples of heterostructure-based strain sensors, enabled by the inkjet printing technology.
rate research
Read More
A well-defined insulating layer is of primary importance in the fabrication of passive (e.g. capacitors) and active (e.g. transistors) components in integrated circuits. One of the most widely known 2-Dimensional (2D) dielectric materials is hexagonal boron nitride (hBN). Solution-based techniques are cost-effective and allow simple methods to be used for device fabrication. In particular, inkjet printing is a low-cost, non-contact approach, which also allows for device design flexibility, produces no material wastage and offers compatibility with almost any surface of interest, including flexible substrates. In this work we use water-based and biocompatible graphene and hBN inks to fabricate all-2D material and inkjet-printed capacitors. We demonstrate an areal capacitance of 2.0 pm 0.3 nF cm^(-2) for a dielectric thickness of sim 3 mu m and negligible leakage currents, averaged across more than 100 devices. This gives rise to a derived dielectric constant of 6.1 pm 1.7. The inkjet printed hBN dielectric has a breakdown field of 1.9 pm 0.3 MV cm^(-1). Fully printed capacitors with sub-/mu m hBN layer thicknesses have also been demonstrated. The capacitors are then exploited in two fully printed demonstrators: a resistor-capacitor (RC) low-pass filter and a graphene-based field effect transistor.
Fully exploiting the properties of 2D crystals requires a mass production method able to produce heterostructures of arbitrary complexity on any substrate, including plastic. Solution processing of graphene allows simple and low-cost techniques such as inkjet printing to be used for device fabrication. However, available inkjet printable formulations are still far from ideal as they are either based on toxic solvents, have low concentration, or require time-consuming and expensive formulation processing. In addition, none of those formulations are suitable for thin-film heterostructure fabrication due to the re-mixing of different 2D crystals, giving rise to uncontrolled interfaces, which results in poor device performance and lack of reproducibility. In this work we show a general formulation engineering approach to achieve highly concentrated, and inkjet printable water-based 2D crystal formulations, which also provides optimal film formation for multi-stack fabrication. We show examples of all-inkjet printed heterostructures, such as large area arrays of photosensors on plastic and paper and programmable logic memory devices, fully exploiting the design flexibility of inkjet printing. Finally, dose-escalation cytotoxicity assays in vitro also confirm the inks biocompatible character, revealing the possibility of extending use of such 2D crystal formulations to drug delivery and biomedical applications.
We report the fabrication of a low cost, and highly reproducible large scale surface-enhanced Raman spectroscopy substrate using an inkjet-printed Ag nanoparticle ink (AgNI). The AgNI SERS substrates were evaluated for SERS using BPY as a molecular probe. The printed AgNI dot arrays exhibit an excellent SERS performance and reproducibility. The batch to batch and spot to spot standard deviation value of less than 10 percent was obtained. The results reveal the reproducibility of the AgNI SERS dot arrays and its potential application for SERS substrates.
The use of natural or bioinspired materials to develop edible electronic devices is a potentially disruptive technology that can boost point-of-care testing. The technology exploits devices which can be safely ingested, along with pills or even food, and operated from within the gastrointestinal tract. Ingestible electronics could potentially target a significant number of biomedical applications, both as therapeutic and diagnostic tool, and this technology may also impact the food industry, by providing ingestible or food-compatible electronic tags that can smart track goods and monitor their quality along the distribution chain. We hereby propose temporary tattoo-paper as a simple and versatile platform for the integration of electronics onto food and pharmaceutical capsules. In particular, we demonstrate the fabrication of all-printed Organic Field-Effect Transistors (OFETs) on untreated commercial tattoo-paper, and their subsequent transfer and operation on edible substrates with a complex non-planar geometry.
The unique properties and atomic thickness of two-dimensional (2D) materials enable smaller and better nanoelectromechanical sensors with novel functionalities. During the last decade, many studies have successfully shown the feasibility of using suspended membranes of 2D materials in pressure sensors, microphones, accelerometers, and mass and gas sensors. In this review, we explain the different sensing concepts and give an overview of the relevant material properties, fabrication routes, and device operation principles. Finally, we discuss sensor readout and integration methods and provide comparisons against the state of the art to show both the challenges and promises of 2D material-based nanoelectromechanical sensing.
Log in to be able to interact and post comments
comments
Fetching comments
Sign in to be able to follow your search criteria
