Subscribe to the gold package and get unlimited access to Shamra Academy
Register a new userSurface stress effects on the electrostatic pull-in instability of nanomechanical systems
79
0
0.0
(
0
)
Authors
Hamed Sadeghian
Ask ChatGPT about the research
No Arabic abstract
The electrostatic pull-in instability (EPI), within the framework of the nanoelectromechanical systems (NEMS) has been shown as a robust and versatile method for characterizing mechanical properties of nanocantilevers. This paper aims to investigate the surface effects, specifically residual surface stress and surface elasticity, on the EPI of micro and nano-scale cantilevers as well as double clamped beams. Since the cantilever has one end free, it has no residual stress, thus the strain-independent component of the surface stress or intrinsic surface stress has no influence on the EPI, as long as it has small deformation. The strain-dependent component of the surface stress or surface elasticity changes the bending stiffness of the cantilever and, consequently, induces shifts in the EPI. For double clamped beams, the effective residual surface stress comes into play and modifies the effective residual stress of the beam. The nonlinear electromechanical coupled equations, which take into account the surface effects are solved numerically. The theoretical results presented in this paper indicate that the EPI is very sensitive to the surface effects, especially when a double clamped beam is employed. The results show that the influence of surface effects on the EPI of cantilevers become more profound when the thickness is below 50 nm, while the influence on double clamped beams is significant even at sub-micron scale. The present study can provide helpful insights for the design and characterization of NEMS switches. Moreover, the results can be used to provide the proof of concepts of a new surface stress sensing method using EPI in nanomechanical sensor systems.
rate research
Read More
We present a unique experimental configuration that allows us to determine the interfacial forces on nearly parallel plates made from the thinnest possible mechanical structures, single and few layer graphene membranes. Our approach consists of using a pressure difference across a graphene membrane to bring the membrane to within ~ 10-20 nm above a circular post covered with SiOx or Au until a critical point is reached whereby the membrane snaps into adhesive contact with the post. Continuous measurements of the deforming membrane with an AFM coupled with a theoretical model allow us to deduce the magnitude of the interfacial forces between graphene and SiOx and graphene and Au. The nature of the interfacial forces at ~ 10 - 20 nm separations is consistent with an inverse fourth power distance dependence, implying that the interfacial forces are dominated by van der Waals interactions. Furthermore, the strength of the interactions is found to increase linearly with the number of graphene layers. The experimental approach can be used to measure the strength of the interfacial forces for other atomically thin two-dimensional materials, and help guide the development of nanomechanical devices such as switches, resonators, and sensors.
This paper presents results about fabrication and operation of electrostatic actuators in liquids with various permittivities. In the static mode, we provide experimental and theoretical demonstration that the pull-in effect can be shifted beyond one third of the initial gap and even be eliminated when electrostatic actuators are operated in liquids. This should benefit to applications in microfluidics requiring either binary state actuation (e.g. pumps, valves) or continuous displacements over the whole gap (e.g. microtweezers). In dynamic mode, actuators like micro-cantilevers present a great interest for Atomic Force Microscopy (AFM) in liquids. As this application requires a good understanding of the cantilever resonance frequency and Q-factor, an analytical modeling in liquid environment has been established. The theoretically derived curves are validated by experimental results using a nitride encapsulated cantilever with integrated electrostatic actuation. Electrode potential screening and undesirable electrochemistry in dielectric liquids are counteracted using AC-voltages. Both experimental and theoretical results should prove useful in micro-cantilever design for AFM in liquids.
The ability to directly observe electronic band structure in modern nanoscale field-effect devices could transform understanding of their physics and function. One could, for example, visualize local changes in the electrical and chemical potentials as a gate voltage is applied. One could also study intriguing physical phenomena such as electrically induced topological transitions and many-body spectral reconstructions. Here we show that submicron angle-resolved photoemission (micro-ARPES) applied to two-dimensional (2D) van der Waals heterostructures affords this ability. In graphene devices, we observe a shift of the chemical potential by 0.6 eV across the Dirac point as a gate voltage is applied. In several 2D semiconductors we see the conduction band edge appear as electrons accumulate, establishing its energy and momentum, and observe significant band-gap renormalization at low densities. We also show that micro-ARPES and optical spectroscopy can be applied to a single device, allowing rigorous study of the relationship between gate-controlled electronic and excitonic properties.
A combination of micro-Raman spectroscopy and micro-XPS (X-ray photo-electron spectroscopy) mapping on statically deflected p-type silicon cantilevers is used to study the mechanical stress dependence of the Fermi level pinning at an oxidized silicon (001) surface. With uniaxial compressive and tensile stress applied parallel to the $langle$110$rangle$ crystal direction, the observations are relevant to the electronic properties of strain-silicon nano-devices with large surface-to-volume ratios such as nanowires and nanomembranes. The surface Fermi level pinning is found to be even in applied stress, a fact that may be related to the symmetry of the Pb$_0$ silicon/oxide interface defects. For stresses up to 160 MPa, an increase in the pinning energy of 0.16 meV/MPa is observed for compressive stress, while for tensile stress it increases by 0.11 meV/MPa. Using the bulk, valence band deformation potentials the reduction in surface band bending in compression (0.09 meV/MPa) and in tension (0.13 meV/MPa) can be estimated.
We present a fully general derivation of the Laplace--Young formula and discuss the interplay between the intrinsic surface geometry and the extrinsic one ensuing from the immersion of the surface in the ordinary euclidean three-dimensional space. We prove that the (reversible) work done in a general surface deformation can be expressed in terms of the surface stress tensor and the variation of the intrinsic surface metric.
Log in to be able to interact and post comments
comments
Fetching comments
Sign in to be able to follow your search criteria
