Subscribe to the gold package and get unlimited access to Shamra Academy
Register a new userMulti-resonant silver nano-disk patterned thin film hydrogenated amorphous silicon solar cells for Staebler-Wronski effect compensation
92
0
0.0
(
0
)
Ask ChatGPT about the research
No Arabic abstract
We study polarization independent improved light trapping in commercial thin film hydrogenated amorphous silicon (a-Si:H) solar photovoltaic cells using a three-dimensional silver array of multi-resonant nano-disk structures embedded in a silicon nitride anti-reflection coating (ARC) to enhance optical absorption in the intrinsic layer (i-a-Si:H) for the visible spectrum for any polarization angle. Predicted total optical enhancement (OE) in absorption in the i-a-Si:H for AM-1.5 solar spectrum is 18.51% as compared to the reference, and producing a 19.65% improvement in short-circuit current density (JSC) over 11.7 mA/cm2 for a reference cell. The JSC in the nano-disk patterned solar cell (NDPSC) was found to be higher than the commercial reference structure for any incident angle. The NDPSC has a multi-resonant optical response for the visible spectrum and the associated mechanism for OE in i-a-Si:H layer is excitation of Fabry-Perot resonance facilitated by surface plasmon resonances. The detrimental Staebler-Wronski effect (SWE) in a-Si:H solar cell can be minimized by the additional OE in the NDPSC and self-annealing of defect states by additional heat generation, thus likely improving the overall stabilized characteristics of a-Si:H solar cells.
rate research
Read More
Great achievements in last five years, such as record-efficient amorphous/crystalline silicon heterojunction (SHJ) solar cells and cutting-edge perovskite/SHJ tandem solar cells, place hydrogenated amorphous silicon (a-Si:H) at the forefront of emerging photovoltaics. Due to the extremely low doping efficiency of trivalent boron (B) in amorphous tetravalent silicon, light harvesting of aforementioned devices are limited by their fill factors (FF), which is a direct metric of the charge carrier transport. It is challenging but crucial to develop highly conductive doped a-Si:H for minimizing the FF losses. Here we report intensive light soaking can efficiently boost the dark conductance of B-doped a-Si:H thin films, which is an abnormal Staebler-Wronski effect. By implementing this abnormal effect to SHJ solar cells, we achieve a certificated power conversion efficiency (PCE) of 25.18% (26.05% on designated area) with FF of 85.42% on a 244.63-cm2 wafer. This PCE is one of the highest reported values for total-area top/rear contact silicon solar cells. The FF reaches 98.30 per cent of its Shockley-Queisser limit.
A methodology is proposed for finding structures that are, optically speaking, locally optimal : a physical analysis of much simpler structures is used to constrain the optimization process. The obtained designs are based on a flat amorphous silicon layer (to minimize recombination) with a patterned anti-reflective coating made of ITO or ZnO, or a composite ITO/ZnO coating. These latter structures are realistic and present good performances despite very thin active layers.
We report on very high enhancement of thin layers absorption through band-engineering of a photonic crystal structure. We realized amorphous silicon (aSi) photonic crystals, where slow light modes improve absorption efficiency. We show through simulation that an increase of the absorption by a factor of 1.5 is expected for a film of aSi. The proposal is then validated by an experimental demonstration, showing an important increase of the absorption of a layer of aSi over a spectral range of 0.32-0.76 microns.
Historically, the design of hybrid solar photovoltaic thermal (PVT) systems has focused on cooling crystalline silicon (c-Si)-based photovoltaic (PV) devices to avoid temperature-related losses. This approach neglects the associated performance losses in the thermal system and leads to a decrease in the overall exergy of the system. Consequently, this paper explores the use of hydrogenated amorphous silicon (a-Si:H) as an absorber material for PVT in an effort to maintain higher and more favourable operating temperatures for the thermal system. Amorphous silicon not only has a smaller temperature coefficient than c-Si, but also can display improved PV performance over extended periods of higher temperatures by annealing out defect states from the Staebler-Wronski effect. In order to determine the potential improvements in a-Si:H PV performance associated with increased thicknesses of the i-layers made possible by higher operating temperatures, a-Si:H PV cells were tested under 1 sun illumination (AM1.5) at temperatures of 25oC (STC), 50oC (representative PV operating conditions), and 90 oC (representative PVT operating conditions). PV cells with an i-layer thicknesses of 420, 630 and 840 nm were evaluated at each temperature. Results show that operating a-Si:H-based PV at 90 oC, with thicker i-layers than the cells currently used in commercial production, provided a greater power output compared to the thinner cells operating at either PV or PVT operating temperatures. These results indicate that incorporating a-Si:H as the absorber material in a PVT system can improve the thermal performance, while simultaneously improving the electrical performance of a-Si:H-based PV.
One of the remaining obstacles to approaching the theoretical efficiency limit of crystalline silicon (c-Si) solar cells is the exceedingly high interface recombination loss for minority carriers at the Ohmic contacts. In ultra-thin-film c-Si solar cells, this contact recombination loss is far more severe than for traditional thick cells due to the smaller volume and higher minority carrier concentration of the former. This paper presents a novel design of an electron passing (Ohmic) contact to n-type Si that is hole-blocking with significantly reduced hole recombination. This contact is formed by depositing a thin titanium dioxide (TiO2) layer to form a silicon metal-insulator-semiconductor (MIS) contact. A 2 {mu}m thick Si cell with this TiO2 MIS contact achieved an open circuit voltage (Voc) of 645 mV, which is 10 mV higher than that of an ultra-thin cell with a metal contact. This MIS contact demonstrates a new path for ultra-thin-film c-Si solar cells to achieve high efficiencies as high as traditional thick cells, and enables the fabrication of high-efficiency c-Si solar cells at a lower cost.
Log in to be able to interact and post comments
comments
Fetching comments
Sign in to be able to follow your search criteria
