Subscribe to the gold package and get unlimited access to Shamra Academy
Register a new userTowards the Realization of Higher Connectivity in MgB2 Conductors: In-situ or Sintered Ex-situ?
158
0
0.0
(
0
)
Ask ChatGPT about the research
No Arabic abstract
The two most common types of MgB2 conductor fabrication technique - in-situ and ex-situ - show increasing conflicts concerning the connectivity, an effective current-carrying cross-sectional area. An in-situ reaction yields a strong intergrain coupling with a low packing factor, while an ex-situ process using pre-reacted MgB2 yields tightly packed grains, however, their coupling is much weaker. We studied the normal-state resistivity and microstructure of ex-situ MgB2 bulks synthesized with varied heating conditions under ambient pressure. The samples heated at moderately high temperatures of ~900{deg}C for a long period showed an increased packing factor, a larger intergrain contact area and a significantly decreased resistivity, all of which indicate the solid-state self-sintering of MgB2. Consequently the connectivity of the sintered ex-situ samples exceeded the typical connectivity range 5-15% of the in-situ samples. Our results show self-sintering develops the superior connectivity potential of ex-situ MgB2, though its intergrain coupling is not yet fulfilled, to provide a strong possibility of twice or even much higher connectivity in optimally sintered ex-situ MgB2 than in in-situ MgB2.
rate research
Read More
In DC and AC practical applications of MgB2 superconducting wires an important role is represented by the material sheath which has to provide, among other things, a suitable electrical and thermal stabilization. A way to obtain a large enough amount of low resistivity material in to the conductor architecture is to use it as external sheath. In this paper we study ex-situ multifilamentary MgB2 wires using oxide-dispersion-strengthened copper (GlidCop) as external sheath in order to reach a good compromise between critical current density and thermal properties. We prepared three GlidCop samples differing by the content of dispersed sub-microscopic Al2O3 particles. We characterized the superconducting and thermal properties and we showed that the good thermal conductivity together the good mechanical properties and a reasonable critical current density make of GlidCop composite wire a useful conductor for applications where high thermal conductivity is request at temperature above 30K, such as Superconducting-FCL.
The thermal properties are one of the key parameters to control phase purity and microstructure of polycrystalline materials. The melting point of the iron-based BaFe2As2 superconductor (Ba122), which foresees high-field applications, remains controversial. In this work, thermogravimetry-differential scanning calorimetry measurements (TG-DSC) of undoped and Co-doped Ba122 were carried out. Mixtures of elemental metals and pre-reacted Ba122 powders were prepared to investigate the thermal responses during in situ and ex situ synthesis routes, respectively. In addition, the phases and microstructures of the quenched samples were evaluated to elucidate the observed exothermic/endothermic peaks. Our results suggest that the melting point of Ba122 is ~1300{deg}C.
Two types of MgB2 films were prepared by pulsed laser deposition (PLD) with in situ and ex situ annealing processes respectively. Significant differences in properties between the two types of films were found. The ex situ MgB2 film has a Tc of 38.1K, while the in situ film has a depressed Tc of 34.5K. The resistivity at 40K for the in situ film is larger than that of the ex situ film by a factor of 6. The residual resistivity ratios (RRR) are 1.1 and 2.1 for the in situ and ex situ films respectively. The Jc-H curves of the in situ film show a much weaker field dependence than those of the ex situ film, attributable to stronger flux pinning in the in situ film. The small-grain feature and high oxygen level may be critical for the significant improvement of Jc in the in situ annealed MgB2 film.
Ex-situ Powder-In-Tube MgB2 tapes prepared with ball-milled, undoped powders showed a strong enhancement of the irreversibility field H*, the upper critical field Hc2 and the critical current density Jc(H) together with the suppression of the anisotropy of all of these quantities. Jc reached 104 A/cm2 at 4.2 K and 10 T, with an irreversibility field of about 14 T at 4.2 K, and Hc2 of 9 T at 25 K, high values for not-doped MgB2. The enhanced Jc and H* values are associated with significant grain refinement produced by milling of the MgB2 powder, which enhances grain boundary pinning, although at the same time also reducing the connectivity from about 12% to 8%. Although enhanced pinning and diminished connectivity are in opposition, the overall influence of ball milling on Jc is positive because the increased density of grains with a size comparable with the mean free path produces strong electron scattering that substantially increases Hc2, especially Hc2 perpendicular to the Mg and B planes.
We report on the superconducting performance of the ex-situ SiC doped MgB2 monofilamentary tapes. Polycrystalline powders of MgB2 doped with 5 and 10 wt% SiC were synthesized by conventional solid-state reaction route and characterized for their superconducting performance. It is found that superconducting parameters i.e. upper critical field (Hc2), irreversibility field (Hirr) and critical current density (Jc) are all improved significantly with SiC addition. Also it was found that relatively lower synthesis temperature (700 C) resulted in further improved superconducting parameters. As synthesized powders are used for ex-situ powder-in-tube (PIT) monofilamentary tapes and superconducting parameters are determined. Albeit the superconducting transition temperature (Tc) is decreased slightly (2K) for SiC doped tapes, the superconducting performance in terms of critical current density (Jc), being determined from both magnetization and transport measurements, is improved significantly. In particular the SiC doped and 700 {deg}C synthesized MgB2 tapes exhibited the transport Jc of nearly 10^4 A/cm2 under applied fields of as high as 7 Tesla. Further it is found that the Jc anisotropy decreases significantly for SiC doped tapes. Disorder due to substitution of C at B site being created from broken SiC and the presence of nano SiC respectively in SiC added ex-situ MgB2 tapes are responsible for decreased anisotropy and improved Jc(H) performance.
Log in to be able to interact and post comments
comments
Fetching comments
Sign in to be able to follow your search criteria
