Subscribe to the gold package and get unlimited access to Shamra Academy
Register a new userUltra-sensitive detection of mode splitting in active optical microcavities
325
0
0.0
(
0
)
Added by
Sahin Kaya Ozdemir Dr
Publication date
2010
fields
Physics
and research's language is
English
Ask ChatGPT about the research
No Arabic abstract
Scattering induced mode splitting in active microcavities is demonstrated. Below the lasing threshold, quality factor enhancement by optical gain allows resolving, in the wavelength-scanning transmission spectrum, the resonance dips of the split modes which otherwise would not be detected in a passive resonator. In the lasing regime, mode splitting manifests itself as two lasing modes with extremely narrow linewidths. Mixing of these laser modes in a detector leads to a heterodyne beat signal whose frequency corresponds to the amount of splitting. Lasing regime not only allows ultrahigh sensitivity for mode-splitting measurements but also provides an easily accessible scheme by eliminating the need for wavelength scanning around resonant modes. Mode splitting in active microcavities has immediate impact in enhancing the sensitivity of sub-wavelength scatterer detection and in studying light-matter interactions in strong coupling regime.
rate research
Read More
The Kerr effect in optical microresonators plays an important role for integrated photonic devices and enables third harmonic generation, four-wave mixing, and the generation of microresonator-based frequency combs. Here we experimentally demonstrate that the Kerr nonlinearity can split ultra-high-Q microresonator resonances for two continuous-wave lasers. The resonance splitting is induced by self- and cross-phase modulation and counter-intuitively enables two lasers at different wavelengths to be simultaneously resonant in the same microresonator mode. We develop a pump-probe spectroscopy scheme that allows us to measure power dependent resonance splittings of up to 35 cavity linewidths (corresponding to 52 MHz) at 10 mW of pump power. The required power to split the resonance by one cavity linewidth is only 286${mu}$W. In addition, we demonstrate threefold resonance splitting when taking into account four-wave mixing and two counterpropagating probe lasers. These Kerr splittings are of interest for applications that require two resonances at optically controlled offsets, eg. for opto-mechanical coupling to phonon modes, optical memories, and precisely adjustable spectral filters.
Plasmonic lasers provide a paradigm-changing approach for the generation of coherent light at the nanoscale. In addition to the usual properties of coherent radiation, the emission of plasmonic lasers can feature high sensitivity to the surrounding environment, which makes this technology attractive for developing high-performance and highly-integrated sensing devices. Here, we investigate a plasmonic laser architecture based on a high-Q plasmonic crystal consisting of a periodic arrangement of nanoholes on a thin gold film cladded with an organic-dye-doped SiO$_2$ gain layer as the gain material. We report an extensive full-wave numerical analysis of the devices lasing performance and its application as a biochemical sensor, showing that the proposed design features excellent figures of merit for surface sensing that in principle can be over an order of magnitude larger than those of previously reported high-performance plasmonic biosensor architectures.
Optical microcavities confine light spatially and temporally and find application in a wide range of fundamental and applied studies. In many areas, the microcavity figure of merit is not only determined by photon lifetime (or the equivalent quality-factor, Q), but also by simultaneous achievement of small mode volume V . Here we demonstrate ultra-high Q-factor small mode volume toroid microcavities on-a-chip, which exhibit a Q/V factor of more than $10^{6}(lambda/n)^{-3}$. These values are the highest reported to date for any chip-based microcavity. A corresponding Purcell factor in excess of 200 000 and a cavity finesse of $2.8times10^{6}$ is achieved, demonstrating that toroid microcavities are promising candidates for studies of the Purcell effect, cavity QED or biochemical sensing
We study the mechanical stability of a tunable high-finesse microcavity under ambient conditions and investigate light-induced effects that can both suppress and excite mechanical fluctuations. As an enabling step, we demonstrate the ultra-precise electronic stabilization of a microcavity. We then show that photothermal mirror expansion can provide high-bandwidth feedback and improve cavity stability by almost two orders of magnitude. At high intracavity power, we observe self-oscillations of mechanical resonances of the cavity. We explain the observations by a dynamic photothermal instability, leading to parametric driving of mechanical motion. For an optimized combination of electronic and photothermal stabilization, we achieve a feedback bandwidth of $500,$kHz and a noise level of $1.1 times 10^{-13},$m rms.
We present a joint theoretical and experimental characterization of thermo-refractive noise in high quality factor ($Q$), small mode volume ($V$) optical microcavities. Analogous to well-studied stability limits imposed by Brownian motion in macroscopic Fabry-Perot resonators, microcavity thermo-refractive noise gives rise to a mode volume-dependent maximum effective quality factor. State-of-the-art fabricated microcavities are found to be within one order of magnitude of this bound. We confirm the assumptions of our theory by measuring the noise spectrum of high-$Q/V$ silicon photonic crystal cavities and apply our results to estimate the optimal performance of proposed room temperature, all-optical qubits using cavity-enhanced bulk material nonlinearities.
Log in to be able to interact and post comments
comments
Fetching comments
Sign in to be able to follow your search criteria
