اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدEfficient Electrical Spin Injection from a Magnetic Metal / Tunnel Barrier Contact into a Semiconductor
225
0
0.0
(
0
)
تأليف
Aubrey T. Hanbicki
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
We report electrical spin injection from a ferromagnetic metal contact into a semiconductor light emitting diode structure with an injection efficiency of 30% which persists to room temperature. The Schottky barrier formed at the Fe/AlGaAs interface provides a natural tunnel barrier for injection of spin polarized electrons under reverse bias. These carriers radiatively recombine, emitting circularly polarized light, and the quantum selection rules relating the optical and carrier spin polarizations provide a quantitative, model-independent measure of injection efficiency. This demonstrates that spin injecting contacts can be formed using a widely employed contact methodology, providing a ready pathway for the integration of spin transport into semiconductor processing technology.
قيم البحث
اقرأ أيضاً
We demonstrate spin polarized tunneling from Fe through a SiO2 tunnel barrier into a Si n-i-p heterostructure. Transport measurements indicate that single step tunneling is the dominant transport mechanism. The circular polarization, Pcirc, of the el
ectroluminescence (EL) shows that the tunneling spin polarization reflects Fe majority spin. Pcirc tracks the Fe magnetization, confirming that the spin-polarized electrons radiatively recombining in the Si originate from the Fe. A rate equation analysis provides a lower bound of 30% for the electron spin polarization in the Si at 5 K.
We have demonstrated by electroluminescence the injection of spin polarized electrons through Co/Al2O3/GaAs tunnel barrier into p-doped InAs/GaAs quantum dots embedded in a PIN GaAs light emitting diode. The spin relaxation processes in the p-doped q
uantum dots are characterized independently by optical measurements (time and polarization resolved photoluminescence). The measured electroluminescence circular polarization is about 15 % at low temperature in a 2T magnetic field, leading to an estimation of the electrical spin injection yield of 35%. Moreover, this electroluminescence circular polarization is stable up to 70 K.
We have calculated the spin-polarization effects of a current in a two dimensional electron gas which is contacted by two ferromagnetic metals. In the purely diffusive regime, the current may indeed be spin-polarized. However, for a typical device ge
ometry the degree of spin-polarization of the current is limited to less than 0.1%, only. The change in device resistance for parallel and antiparallel magnetization of the contacts is up to quadratically smaller, and will thus be difficult to detect.
We demonstrate highly efficient spin injection at low and room temperature in an AlGaAs/GaAs semiconductor heterostructure from a CoFe/AlOx tunnel spin injector. We use a double-step oxide deposition for the fabrication of a pinhole-free AlOx tunnel
barrier. The measurements of the circular polarization of the electroluminescence in the Oblique Hanle Effect geometry reveal injected spin polarizations of at least 24% at 80K and 12% at room temperature.
Creating, manipulating and detecting spin polarized carriers are the key elements of spin based electronics. Most practical devices use a perpendicular geometry in which the spin currents, describing the transport of spin angular momentum, are accomp
anied by charge currents. In recent years, new sources of pure spin currents, i.e., without charge currents, have been demonstrated and applied. In this paper, we demonstrate a conceptually new source of pure spin current driven by the flow of heat across a ferromagnetic/non-magnetic metal (FM/NM) interface. This spin current is generated because the Seebeck coefficient, which describes the generation of a voltage as a result of a temperature gradient, is spin dependent in a ferromagnet. For a detailed study of this new source of spins, it is measured in a non-local lateral geometry. We developed a 3D model that describes the heat, charge and spin transport in this geometry which allows us to quantify this process. We obtain a spin Seebeck coefficient for Permalloy of -3.8 microvolt/Kelvin demonstrating that thermally driven spin injection is a feasible alternative for electrical spin injection in, for example, spin transfer torque experiments.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
