اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدFull-color photon-counting single-pixel imaging
188
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
We propose and experimentally demonstrate a high-efficiency single-pixel imaging (SPI) scheme by integrating time-correlated single-photon counting (TCSPC) with time-division multiplexing to acquire full-color images at extremely low light level. This SPI scheme uses a digital micromirror device to modulate a sequence of laser pulses with preset delays to achieve three-color structured illumination, then employs a photomultiplier tube into the TCSPC module to achieve photon-counting detection. By exploiting the time-resolved capabilities of TCSPC, we demodulate the spectrum-image-encoded signals, and then reconstruct high-quality full-color images in a single-round of measurement. Based on this scheme, the strategies such as single-step measurement, high-speed projection, and undersampling can further improve the imaging efficiency.
قيم البحث
اقرأ أيضاً
We demonstrate single-pixel imaging in the spectral domain by encoding Fourier probe patterns onto the spectrum of a superluminescent laser diode using a programmable optical filter. As a proof-of-concept, we measure the wavelength-dependent transmis
sion of a Michelson interferometer and a wavelength-division multiplexer. Our results open new perspectives for remote broadband measurements with possible applications in industrial, biological or security applications.
Under weak illumination, tracking and imaging moving object turns out to be hard. By spatially collecting the signal, single pixel imaging schemes promise the capability of image reconstruction from low photon flux. However, due to the requirement on
large number of samplings, how to clearly image moving objects is an essential problem for such schemes. Here we present a principle of single pixel tracking and imaging method. Velocity vector of the object is obtained from temporal correlation of the bucket signals in a typical computational ghost imaging system. Then the illumination beam is steered accordingly. Taking the velocity into account, both trajectory and clear image of the object are achieved during its evolution. Since tracking is achieved with bucket signals independently, this scheme is valid for capturing moving object as fast as its displacement within the interval of every sampling keeps larger than the resolution of the optical system. Experimentally, our method works well with the average number of detected photons down to 1.88 photons/speckle.
Abstract removed.
Single-pixel imaging is suitable for low light level scenarios because a bucket detector is employed to maximally collect the light from an object. However, one of the challenges is its slow imaging speed, mainly due to the slow light modulation tech
nique. We here demonstrate 1.4MHz video imaging based on computational ghost imaging with a RGB LED array having a full-range frame rate up to 100MHz. With this method, the motion of a high speed propeller is observed. Moreover, by exploiting single-photon detectors to increase the detection efficiency, this method is developed for ultra-high-speed imaging under low light level.
We demonstrated a laser depth imaging system based on the time-correlated single-photon counting technique, which was incorporated with a low-jitter superconducting nanowire single-photon detector (SNSPD), operated at the wavelength of 1550 nm. A sub
-picosecond time-bin width was chosen for photon counting, resulting in a discrete noise of less than one/two counts for each time bin under indoor/outdoor daylight conditions, with a collection time of 50 ms. Because of the low-jitter SNSPD, the target signal histogram was significantly distinguishable, even for a fairly low retro-reflected photon flux. The depth information was determined directly by the highest bin counts, instead of using any data fitting combined with complex algorithms. Millimeter resolution depth imaging of a low-signature object was obtained, and more accurate data than that produced by the traditional Gaussian fitting method was generated. Combined with the intensity of the return photons, three-dimensional reconstruction overlaid with reflectivity data was realized.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
