اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدWettability and surface energy of parylene F
66
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
Parylenes are barrier materials employed as protective layers. However, many parylenes are unsuitable for applications under harsh conditions. A new material, parylene F, demonstrates considerable potential for a wide range of applications due to its high temperature and UV resistance. For the first time, the wettability and surface energy of parylene F were investigated to determine the feasibility of parylene F as an alternative to the commonly employed parylene C. The results show that parylene F has a hydrophobic surface with a water contact angle of 109.63 degrees. We found that 3.5 ul probe liquid is an optimal value for the contact angle measurement of parylene F. Moreover, we found that the Owens-Wendt-Kaelble and the Lifshitz-van der Waals/acid-base approaches are unsuitable for determining the surface energy of parylene F, whereas an approach based on the limitless liquid-solid interface wetting system is compatible. Furthermore, the results show that parylene F has a surface energy of 39.05 mJ/m2. Considering the improved resistance, relatively low cost, and the desirable properties, parylene F can replace parylene C for applications under harsh conditions.
قيم البحث
اقرأ أيضاً
Phosphorene is emerging as a promising 2D semiconducting material with a direct band gap and high carrier mobility. In this paper, we examine the role of the extrinsic point defects including surface adatoms in modifying the electronic properties of
phosphorene using density functional theory. The surface adatoms considered are B, C, N, O and F with a [He] core electronic configuration. Our calculations show that B and C, with electronegativity close to P, prefer to break the sp3 bonds of phosphorene, and reside at the interstitial sites in the 2D lattice by forming sp2 bonds with the native atoms. On the other hand, N, O and F, which are more electronegative than P, prefer the surface sites by attracting the lone pairs of phosphorene. B, N and F adsorption will also introduce local magnetic moment to the lattice. Moreover, B, C, N and F adatoms will modify the band gap of phosphorene yielding metallic transverse tunneling characters. Oxygen does not modify the band gap of phosphorene, and a diode like tunneling behavior is observed. Our results therefore offer a possible route to tailor the electronic and magnetic properties of phosphorene by the adatom functionalization, and provide the physical insights of the environmental sensitivity of phosphorene, which will be helpful to experimentalists in evaluating the performance and aging effects of phosphorene-based electronic devices.
A major goal of energy research is to use visible light to cleave water directly, without an applied voltage, into hydrogen and oxygen. Since the initial reports of the ultraviolet (UV) activity of TiO2 and SrTiO3 in the 1970s, researchers have pursu
ed a fundamental understanding of the mechanistic and molecular-level phenomena involved in photo-catalysis. Although it requires UV light, after four decades SrTiO3 is still the gold standard for splitting water. It is chemically stable and catalyzes both the hydrogen and the oxygen reactions without applied bias. While ultrahigh vacuum (UHV) surface science techniques have provided useful insights, we still know relatively little about the structure of electrodes in contact with electrolytes under operating conditions. Here, we report the surface structure evolution of a SrTiO3 electrode during water splitting, before and after training with a positive bias. Operando high-energy X-ray reflectivity measurements demonstrate that training the electrode irreversibly reorders the surface. Scanning electrochemical microscopy (SECM) at open circuit correlates this training with a tripling of the activity toward photo-induced water splitting. A novel first-principles joint density-functional theory (JDFT) simulation constrained to the X-ray data via a generalized penalty function identifies an anatase-like structure for the more active, trained surface.
We have measured the stopping powers and straggling of fast, highly ionized atoms passing through thin bilayer targets made up of metals and insulators. We were surprised to find that the energy losses as well as the straggling depend on the ordering
of the target and have small but significantly different values on bilayer reversal. We ascribe this newly found difference in energy loss to the surface energy loss field effect due to the differing surface wake fields as the beam exits the target in the two cases. This finding is validated with experiments using several different projectiles, velocities, and bilayer targets. Both partners of the diatomic molecular ions also display similar results. A comparison of the energy loss results with those of previous theoretical predictions for the surface wake potential for fast ions in solids supports the existence of a self-wake.
Wavepacket propagation calculations are reported for the interaction of a Rydberg hydrogen atom ($n=2-8)$ with Cu(111) and Cu(100) surfaces (represented by a Chulkov potential), in comparison with a Jellium surface. Both copper surfaces have a projec
ted band gap at the surface in the energy range degenerate with some or all of the Rydberg energies. The charge transfer of the Rydberg electron to the surface is found to be enhanced for $n$ values at which there is a near-degeneracy between the Rydberg energy level and an image state or a surface state of the surface. The enhancement is facilitated by the strong overlap of the surface image-state orbital lying outside the surface and the orbital of the incoming Rydberg atom. These calculations point to the possibility of using Rydberg-surface collisions as a probe of surface electronic structure.
The free energy profile of a reaction can be estimated in a molecular-dynamics approach by imposing a mechanical constraint along a reaction coordinate (RC). Many recent studies have shown that the temperature can greatly influence the path followed
by the reactants. Here, we propose a practical way to construct the minimum energy path directly on the free energy surface (FES) at a given temperature. First, we follow the blue-moon ensemble method to derive the expression of the free energy gradient for a given RC. These derivatives are then used to find the actual minimum energy reaction path at finite temperature, in a way similar to the Intrinsic Reaction Path of Fukui on the potential energy surface [K Fukui J. Phys. Chem. 74, 4161 (1970)]. Once the path is know, one can calculate the free energy profile using thermodynamic integration. We also show that the mass-metric correction cancels for many types of constraints, making the procedure easy to use. Finally, the minimum free energy path at 300 K for the addition of the 1,1-dichlorocarbene to ethylene is compared with a path based on a simple one-dimensional reaction coordinate. A comparison is also given with the reaction path at 0 K.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
