اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدEnhanced ZnTe infiltration in porous silicon by Isothermal Close Space Sublimation
67
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
Isothermal Close Space Sublimation (ICSS) technique was used for embedding porous silicon (PS) films with ZnTe. It was studied the influence of the preparation conditions and in particular of a chemical etching step before the ZnTe growth, on the composition profile and final porosity of ZnTe embedded PS. The structure of the embedded material was determined by x-ray diffraction analysis while the thickness of the samples was determined by scanning electron microscopy (SEM). Rutherford backscattering (RBS) and Energy Dispersive (EDS) spectrometries allowed determining the composition profiles. We conclude that the etching of the PS surface before the ZnTe growth has two main effects: the increase of the porosity and enhancing the reactivity of the inner surface. It was observed that both effects benefit the filling process of the pores. Since RBS and EDS cannot detect the porosity in the present system, we explore the evolution of porosity by the fitting of the UV-VIS reflectance spectra. The atomic percent determined with this method was in relatively good agreement with that obtained from the RBS and EDS measurements.
قيم البحث
اقرأ أيضاً
The role of the sublimation of the compound and of the evaporation of the constituents from the gold nanoparticle during the growth of semiconductor nanowires is exemplified with CdTe-ZnTe heterostructures. Operating close to the upper temperature li
mit strongly reduces the amount of Cd present in the gold nanoparticle and the density of adatoms on the nanowire sidewalls. As a result, the growth rate is small and strongly temperature dependent, but a good control of the growth conditions allows the incorporation of quantum dots in nanowires with sharp interfaces and adjustable shape, and it minimizes the radial growth and the subsequent formation of additional CdTe clusters on the nanowire sidewalls, as confirmed by photoluminescence. Uncapped CdTe segments dissolve into the gold nanoparticle when interrupting the flux, giving rise to a bulb-like (pendant-droplet) shape attributed to the Kirkendall effect.
Porous silicon layers were embedded with ZnTe using the isothermal close space sublimation technique. The presence of ZnTe was demonstrated using cross-sectional energy dispersive spectroscopy maps. ZnTe embedded samples present intense room temperat
ure photoluminescence along the whole visible range. We ascribe this PL to ZnTe nanocrystals of different sizes grown on the internal pore surface. Such crystals, with different orientations and sizes, were observed in transmission electron microscopy images, while transmission electron diffraction images of the same regions reveal ZnTe characteristic patterns.
Thermoelectric device is a promising next-generation energy solution owing to its capability to transform waste heat into useful electric energy, which can be realized in materials with high elec- tric conductivities and low thermal conductivities. A
recently synthesized silicon allotrope of Si$_{24}$ features highly anisotropic crystal structure with nanometre-sized regular pores. Here, based on first-principles study without any empirical parameter, we show that the slightly doped Si$_{24}$ can pro- vide an order-of-magnitude enhanced thermoelectric figure of merit at room temperature, compared with the cubic diamond phase of silicon. We ascribe the enhancement to the intrinsic nanostructure formed by the nanopore array, which effectively hinders heat conduction while electric conductivity is maintained. This can be a viable option to enhance the thermoelectric figure of merit without further forming an extrinsic nanostructure. In addition, we propose a practical strategy to further diminish the thermal conductivity without affecting electric conductivity by confining rattling guest atoms in the pores.
After the pioneering investigations into graphene-based electronics at Georgia Tech (GT), great strides have been made developing epitaxial graphene on silicon carbide (EG) as a new electronic material. EG has not only demonstrated its potential for
large scale applications, it also has become an invaluable material for fundamental two-dimensional electron gas physics showing that only EG is on route to define future graphene science. It was long known that graphene mono and multilayers grow on SiC crystals at high temperatures in ultra-high vacuum. At these temperatures, silicon sublimes from the surface and the carbon rich surface layer transforms to graphene. However the quality of the graphene produced in ultrahigh vacuum is poor due to the high sublimation rates at relatively low temperatures. The GT team developed growth methods involving encapsulating the SiC crystals in graphite enclosures, thereby sequestering the evaporated silicon and bringing growth process closer to equilibrium. In this confinement controlled sublimation (CCS) process, very high quality graphene is grown on both polar faces of the SiC crystals. Since 2003, over 50 publications used CCS grown graphene, where it is known as the furnace grown graphene. Graphene multilayers grown on the carbon-terminated face of SiC, using the CCS method, were shown to consist of decoupled high mobility graphene layers. The CCS method is now applied on structured silicon carbide surfaces to produce high mobility nano-patterned graphene structures thereby demonstrating that EG is a viable contender for next-generation electronics. Here we present the CCS method and demonstrate several of epitaxial graphenes outstanding properties and applications.
Chemically _ driven isothermal close space vapour transport was used to prepare pure MoO2 films which were eventually converted to MoO3 by annealing in air. According to temperature_dependent Raman measurements, the MoO2/MoO3 phase transformation was
found to occur in the 225 _ 350 oC range; no other phases were detected during the transition. A clear change in composition and Raman spectra, as well as noticeable modifications of the band gap and the absorption coefficient confirmed the conversion from MoO2 to MoO3. An extensive characterization of films of both pure phases was carried out. In particular, a procedure was developed to determine the dispersion relation of the refractive index of MoO2 from the shift of the interference fringes the used SiO2/Si substrate. The obtained refractive index was corrected taking into account the porosity calculated from elastic backscattering spectrometry. The Debye temperature and the residual resistivity were extracted from the electrical resistivity temperature dependence using the Bloch _ Gruneisen equation. MoO3 converted samples presented very high resistivity and a typical semiconducting behaviour. They also showed intense and broad luminescence spectra, which were deconvoluted considering several contributions; and its behaviour with temperature was examined. Furthermore, surface photovoltage spectra were taken and the relation of these spectra with the photoluminescence is discussed.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
