اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدUltra thin anti-reflective coatings designed using Differential Evolution
57
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
We use a state-of-the-art optimization algorithm combined with a careful methodology to find optimal anti-reflective coatings. Our results show that ultra thin structures (less than $300 ,nm$ thick) outperform much thicker gradual patterns as well as traditional interferential anti-reflective coatings. These optimal designs actually combine a gradual increase of the refractive index with patterns meant to leverage interferential effects. Contrarily to gradual patterns, they do not require extremely low refractive index materials, so that they can actually be fabricated. Using a cheap and easily deployable vapor deposition technique, we fabricated a 4-layer anti-reflective coating, which proved very efficient over the whole visible spectrum despite a total thickness of only 200 nm.
قيم البحث
اقرأ أيضاً
The desire for higher sensitivity has driven ground-based cosmic microwave background (CMB) experiments to employ ever larger focal planes, which in turn require larger reimaging optics. Practical limits to the maximum size of these optics motivates
the development of quasi-optically-coupled (lenslet-coupled), multi-chroic detectors. These detectors can be sensitive across a broader bandwidth compared to waveguide-coupled detectors. However, the increase in bandwidth comes at a cost: the lenses (up to $sim$700 mm diameter) and lenslets ($sim$5 mm diameter, hemispherical lenses on the focal plane) used in these systems are made from high-refractive-index materials (such as silicon or amorphous aluminum oxide) that reflect nearly a third of the incident radiation. In order to maximize the faint CMB signal that reaches the detectors, the lenses and lenslets must be coated with an anti-reflective (AR) material. The AR coating must maximize radiation transmission in scientifically interesting bands and be cryogenically stable. Such a coating was developed for the third generation camera, SPT-3G, of the South Pole Telescope (SPT) experiment, but the materials and techniques used in the development are general to AR coatings for mm-wave optics. The three-layer polytetrafluoroethylene-based AR coating is broadband, inexpensive, and can be manufactured with simple tools. The coating is field tested; AR coated focal plane elements were deployed in the 2016-2017 austral summer and AR coated reimaging optics were deployed in 2017-2018.
ASTRI is a Flagship Project of the Italian Ministry of Education, University and Research, led by the Italian National Institute of Astrophysics, INAF. One of the main aims of the ASTRI Project is the design, construction and verification on-field of
a dual mirror (2M) end-to-end prototype for the Small Size Telescope (SST) envisaged to become part of the Cherenkov Telescope Array. The ASTRI SST-2M prototype adopts the Schwarzschild-Couder design, and a camera based on SiPM (Silicon Photo Multiplier); it will be assembled at the INAF astronomical site of Serra La Nave on mount Etna (Catania, Italy) within mid 2014, and will start scientific validation phase soon after. The peculiarities of the optical design and of the SiPM bandpass pushed towards specifically optimized choices in terms of reflective coatings for both the primary and the secondary mirror. In particular, multi-layer dielectric coatings, capable of filtering out the large Night Sky Background contamination at wavelengths $lambda gtrsim 700$ nm have been developed and tested, as a solution for the primary mirrors. Due to the conformation of the ASTRI SST-2M camera, a reimaging system based on thin pyramidal light guides could be optionally integrated aiming to increase the fill factor. An anti-reflective coating optimized for a wide range of incident angles faraway from normality was specifically developed to enhance the UV-optical transparency of these elements. The issues, strategy, simulations and experimental results are thoroughly presented.
Anti-reflective coatings (ARCs) are used on the vast majority of solar photovoltaic (PV) modules to increase power production. However, ARC longevity can vary from less than 1 year to over 15 years depending on coating quality and deployment conditio
ns. A technique that can quantify ARC degradation non-destructively on commercial modules would be useful both for in-field diagnostics and accelerated aging tests. In this paper, we demonstrate that accurate measurements of ARC spectral reflectance can be performed using a modified commercially-available integrating-sphere probe. The measurement is fast, accurate, non-destructive and can be performed outdoors in full-sun conditions. We develop an interferometric model that estimates coating porosity, thickness and fractional area coverage from the measured reflectance spectrum for a uniform single-layer coating. We demonstrate the measurement outdoors on an active PV installation, identify the presence of an ARC and estimate the properties of the coating.
The relationships between material constructions and reflective spectrum patterns are important properties of photonic crystals. One particular interesting reflectance profile is a high-intensity and uniform three-peak pattern with peak positions rig
ht located at the red, green, and blue (RGB, three original colors) region. For ease of construction, a seek for using one-dimensional photonic crystals to achieve RGB triple reflective bands is a meaningful endeavor. Only very limited previous studies exist, all relying on traditional periodic photonic crystals (PPCs) and of large thickness. The underlying physical principles remain elusive, leaving the question of thickness limit to achieve RGB bands unaddressed. Here, we present the first detailed work to explore the thickness limit issue based on both theoretical and experimental investigation. A set of heuristically derived design principles are used to uncover that the break of translational symmetry, thus introducing heterostructure photonic crystals (HPCs), is essential to reduce the total optical path difference (OPD) to ~ 3200nm (the theoretical limit) while still exhibiting high-quality RGB bands. A systematic experiment based on a 12-layer heterostructure construction was performed and well confirmed the theoretical predictions. The associated three-peak properties are successfully used to realize quantum dot fluorescent enhancement phenomena. Furthermore, the HPC exhibits unusually stability against solvent stimulus, in strong contrast to typical behaviors reported in PPCs. Our work for the first time proposes and verifies important rational rules for designing ultrathin HPCs toward RGB reflective bands, and provides insights for a wider range of explorations of light manipulation in photonic crystals.
For generation of sustainable, clean and highly efficient energy, the electrocatalytic oxygen evolution reaction represents an attractive platform, thus inviting immense research activities in recent years. However, designing the catalyst with enhanc
ed electrocatalytic activity remains one of the major challenges. Here, we examined the oxygen evolution reaction activities of geometrically designed (with and without step-textured morphology) thin films of an electrocatalytically active correlated metallic SrRuO3 perovskite grown on c- and r-plane sapphire substrates. On c-plane sapphire, as compared to the uniform surface, the step-textured films endowed with active Ru-sites show remarkable decrease in the overpotential (25 mV). Interestingly, the behavior is opposite for the r-plane case, highlighting the significance of the active sites, in addition with the polar surface termination of selective crystal facets. Density functional theory calculation confirms the favorable energy reaction pathway for the active site dependent enhancement in OER. Our strategy might pave the way towards designing the surfaces of various oxide thin films for high performance energy conversion based devices.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
