ترغب بنشر مسار تعليمي؟ اضغط هنا

Growth, Morphology and Stability of Au in Contact with the Bi2Se3(0001) Surface

103   0   0.0 ( 0 )
 نشر من قبل Mattia Fanetti
 تاريخ النشر 2019
  مجال البحث فيزياء
والبحث باللغة English




اسأل ChatGPT حول البحث

We report a combined microscopy and spectroscopy study of Au deposited on the Bi2Se3(0001) single crystal surface. At room temperature Au forms islands, according to the Volmer-Weber growth mode. Upon annealing to 100{deg} C the Au deposits are not stable and assemble into larger and thicker islands. The topological surface state of Bi2Se3 is weakly affected by the presence of Au. Contrary to other metals, such as Ag or Cr, a strong chemical instability at the Au/Bi2Se3 interface is ruled out. Core level analysis highlights Bi diffusion toward the surface of Au islands, in agreement with previous findings, while chemical interaction between Au and atomic Se is limited at the interfacial region. For the investigated range of Au coverages, the Au/Bi2Se3 heterostructure is inert towards CO and CO2 exposure at low pressure (10-8 mbar) regime.



قيم البحث

اقرأ أيضاً

Spontaneous formation of grains has been observed for the MnAs layer grown by means of MBE on the GaN(0001)-(1x1) surface. Electronic structure of the system was investigated in situ by resonant photoemission spectroscopy. Density of the valence band states of MnAs and its changes due to increase of the layer thickness were revealed.
We have used density functional theory to study the structural stability of surface alloys. Our systems consist of a single pseudomorphic layer of $M_xN_{1-x}$ on the Ru(0001) surface, where $M$ = Fe or Co, and $N$ = Pt, Au, Ag, Cd, or Pb. Several of the combinations studied by us display a preference for atomically mixed configurations over phase-segregated forms. We have also performed further {it ab initio} calculations to obtain the parameters describing the elastic interactions between atoms in the alloy layer, including the effective atomic sizes at the surface. We find that while elastic interactions favor alloying for all the systems considered by us, in some cases chemical interactions disfavor atomic mixing. We show that a simple criterion (analogous to the Hume-Rothery first law for bulk alloys) need not necessarily work for strain-stabilized surface alloys, because of the presence of additional elastic contributions to the alloy heat of formation, that will tend to oppose phase segregation.
Most spectroscopic methods for studying the electronic structure of metal surfaces have the disadvantage that either only occupied or only unoccupied states can be probed, and the signal is cut at the Fermi edge. This leads to significant uncertainti es, when states are very close to the Fermi level. By performing low-temperature scanning tunneling spectroscopy and ab initio calculations, we study the surface-electronic structure of La(0001) and Lu(0001), and demonstrate that in this way detailed information on the surface-electronic structure very close to the Fermi energy can be derived with high accuracy.
By comparing the growth of Cu thin films on bare and graphene-covered Ru(0001) surfaces, we demonstrate the role of graphene as a surfactant allowing the formation of flat Cu films. Low-energy electron microscopy, X-ray photoemission electron microsc opy and X-ray absorption spectroscopy reveal that depositing Cu at 580 K leads to distinct behaviors on both types of surfaces. On bare Ru, a Stranski-Krastanov growth is observed, with first the formation of an atomically flat and monolayer-thick wetting layer, followed by the nucleation of three-dimensional islands. In sharp contrast, when Cu is deposited on a graphene-covered Ru surface under the very same conditions, Cu intercalates below graphene and grows in a step-flow manner: atomically-high growth fronts of intercalated Cu form at the graphene edges, and extend towards the center of the flakes. Our findings suggest potential routes in metal heteroepitaxy for the control of thin film morphology.
Interfaces of sapphire are of technological relevance as sapphire is used as a substrate in electronics, lasers, and Josephson junctions for quantum devices. In addition, its surface is potentially useful in catalysis. Using first principles calculat ions, we show that, unlike bulk sapphire which has inversion symmetry, the (0001) sapphire surface is piezoelectric. The inherent broken symmetry at the surface leads to a surface dipole and a significant response to imposed strain: the magnitude of the surface piezoelectricity is comparable to that of bulk piezoelectrics.
التعليقات
جاري جلب التعليقات جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
mircosoft-partner

هل ترغب بارسال اشعارات عن اخر التحديثات في شمرا-اكاديميا