ترغب بنشر مسار تعليمي؟ اضغط هنا

A High-performance Track Fitter for Use in Ultra-fast Electronics

118   0   0.0 ( 0 )
 نشر من قبل Ricardo Eusebi Dr.
 تاريخ النشر 2018
  مجال البحث فيزياء
والبحث باللغة English




اسأل ChatGPT حول البحث

This article describes a new charged-particle track fitting algorithm designed for use in high-speed electronics applications such as hardware-based triggers in high-energy physics experiments. Following a novel technique designed for fast electronics, the positions of the hits on the detector are transformed before being passed to a linearized track parameter fit. This transformation results in fitted track parameters with a very linear dependence on the hit positions. The approach is demonstrated in a representative detector geometry based on the CMS detector at the Large Hadron Collider. The fit is implemented in FPGA chips and optimized for track fitting throughput and obtains excellent track parameter performance. Such an algorithm is potentially useful in any high-speed track-fitting application.



قيم البحث

اقرأ أيضاً

The development of Low-Gain Avalanche Detectors has opened up the possibility of manufacturing silicon detectors with signal larger than that of traditional sensors. In this paper we explore the timing performance of Low-Gain Avalanche Detectors, and in particular we demonstrate the possibility of obtaining ultra-fast silicon detector with time resolution of less than 20 picosecond.
91 - Pierre Billoir 2021
We present an alternative implementation of the Kalman filter employed for track fitting within the LHCb experiment. It uses simple parametrizations for the extrapolation of particle trajectories in the field of the LHCb dipole magnet and for the eff ects of multiple scattering in the detector material. A speedup of more than a factor of four is achieved while maintaining the quality of the estimated track quantities. This Kalman filter implementation could be used in the purely software-based trigger of the LHCb upgrade.
Future experiments of nuclear and particle physics are moving towards the high luminosity regime, in order to access suppressed processes like rare B decays or exotic charmonium resonances. In this scenario, high rate capability is a key requirement for electronics instrumentation, together with excellent timing resolution for precise event reconstruction. The development of dedicated FrontEnd Electronics (FEE) for detectors has become increasingly challenging. A current trend in R&D is towards multipurpose FEE which can be easily adapted to a great variety of detectors, without impairing the required high performance. We report on high-precision timing solutions which utilise high-bandwidth preamplifiers and fast discriminators providing Time-over-Threshold information, which can be used for charge measurements or walk corrections thus improving the obtainable timing resolution. The output signal are LVDS and can be directly fed into a multi-hit TDC readout. The performance of the electronics was investigated for single photon signals, typical for imaging Cherenkov detectors. The opposite condition of light signals arising from plastic scintillators, was also studied. High counting rates per channel of several MHz were achieved, and a timing resolution of better than 100 ps could be obtained in a test experiment using the full readout chain.
113 - A. Annovi 2009
The Fast Tracker (FTK) is a proposed upgrade to the ATLAS trigger system that will operate at full Level-1 output rates and provide high quality tracks reconstructed over the entire detector by the start of processing in Level-2. FTK solves the combi natorial challenge inherent to tracking by exploiting the massive parallelism of Associative Memories (AM) that can compare inner detector hits to millions of pre-calculated patterns simultaneously. The tracking problem within matched patterns is further simplified by using pre-computed linearized fitting constants and leveraging fast DSPs in modern commercial FPGAs. Overall, FTK is able to compute the helix parameters for all tracks in an event and apply quality cuts in approximately one millisecond. By employing a pipelined architecture, FTK is able to continuously operate at Level-1 rates without deadtime. The system design is defined and studied using ATLAS full simulation. Reconstruction quality is evaluated for single muon events with zero pileup, as well as WH events at the LHC design luminosity. FTK results are compared with the tracking capability of an offline algorithm.
65 - W. Deng , Z. Song , G. Huang 2020
Real-time track tracking in high energy physics experiments at colliders running at high luminosity is very challenging for trigger systems. To perform pattern-recognition and track fitting in online trigger system, the artificial Retina algorithm ha s been introduced in the field. Retina can be implemented in the state of the art FPGA devices. Our developments use Retina in an iterative way to identify track for barrel-shape tracker embedded in a high magnetic field and with high track multiplicity. As a benchmark we simulate LHC t-tbar events, with a pile-up of 200 and a GEANT-4 based simulation of a 6-layers barrel tracker detector made of silicon modules. With this sample the performance of the hardware design (resource usage, latency) is evaluated. Both efficiency and purity of the Retina fitting are over 90%. Moreover we have also added a Kalman filter after the Retina fit to improve the resolution on the track parameters. Our simulation results show that the Kalman filter can work well together with the Retina algorithm to find track through t-tbar event and provides high resolutions of the reconstructed parameters.
التعليقات
جاري جلب التعليقات جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
mircosoft-partner

هل ترغب بارسال اشعارات عن اخر التحديثات في شمرا-اكاديميا