اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدTitanium diboride ceramics for solar thermal absorbers
88
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
Titanium diboride (TiB2) is a low-density refractory material belonging to the family of ultra-high temperature ceramics (UHTCs). This paper reports on the production and microstructural and optical characterization of nearly fully dense TiB2, with particular interest to its potential utilization as novel thermal solar absorber. Monolithic bulk samples are produced starting from elemental reactants by a two-step method consisting of the Self-propagating High-temperature Synthesis (SHS) followed by the Spark Plasma Sintering (SPS) of the resulting powders. The surface of obtained samples has-been characterized from the microstructural and topological points of view. The hemispherical reflectance spectrum has been measured from 0.3 to 15 um wavelength, to evaluate the potential of this material as solar absorber for future concentrating solar plants.
قيم البحث
اقرأ أيضاً
Various thin-film I$_2$-II-IV-VI$_4$ photovoltaic absorbers derived from kesterite Cu$_2$ZnSn(S,Se)$_4$ have been synthesized, characterized, and theoretically investigated in the past few years. The availability of this homogeneous materials dataset
is an opportunity to examine trends in their defect properties and identify criteria to find new defect-tolerant materials in this vast chemical space. We find that substitutions on the Zn site lead to a smooth decrease in band tailing as the ionic radius of the substituting cation increases. Unfortunately, this substitution strategy does not ensure the suppression of deeper defects and non-radiative recombination. Trends across the full dataset suggest that Gaussian and Urbach band tails in kesterite-inspired semiconductors are two separate phenomena caused by two different antisite defect types. Deep Urbach tails are correlated with the calculated band gap narrowing caused by the (2I$_mathrm{II}$+IV$_mathrm{II}$) defect cluster. Shallow Gaussian tails are correlated with the energy difference between the kesterite and stannite polymorphs, which points to the role of (I$_mathrm{II}$+II$_mathrm{I}$) defect clusters involving Group IB and Group IIB atoms swapping across textit{different} cation planes. This finding can explain why textit{in-plane} cation disorder and band tailing are uncorrelated in kesterites. Our results provide quantitative criteria for discovering new kesterite-inspired photovoltaic materials with low band tailing.
The titanium fire as produced during high pressure and friction is the major failure scenario for aero-engines. To alleviate this issue, Ti-V-Cr and Ti-Cu-Al series burn resistant titanium alloys have been developed. However, which burn resistant all
oy exhibit better property with reasonable cost needs to be evaluated. This work unveils the burning mechanisms of these alloys and discusses whether burn resistance of Cr and V can be replaced by Cu, on which thorough exploration is lacking. Two representative burn resistant alloys are considered, including Ti14(Ti-13Cu-1Al-0.2Si) and Ti40(Ti-25V-15Cr-0.2Si)alloys. Compared with the commercial non-burn resistant titanium alloy, i.e., TC4(Ti-6Al-4V)alloy, it has been found that both Ti14 and Ti40 alloys form protective shields during the burning process. Specifically, for Ti14 alloy, a clear Cu-rich layer is formed at the interface between burning product zone and heat affected zone, which consumes oxygen by producing Cu-O compounds and impedes the reaction with Ti-matrix. This work has established a fundamental understanding of burning resistant mechanisms for titanium alloys. Importantly, it is found that Cu could endow titanium alloys with similar burn resistant capability as that of V or Cr, which opens a cost-effective avenue to design burn resistant titanium alloys.
Majority and minority carrier properties such as type, density and mobility represent fundamental yet difficult to access parameters governing semiconductor device performance, most notably solar cells. Obtaining this information simultaneously under
light illumination would unlock many critical parameters such as recombination lifetime, recombination coefficient, and diffusion length; while deeply interesting for optoelectronic devices, this goal has remained elusive. We demonstrate here a new carrier-resolved photo-Hall technique that rests on a new identity relating hole-electron mobility difference ($Deltamu$), Hall coefficient ($h$), and conductivity ($sigma$): $Deltamu=(2+dln h/dln sigma),h,sigma$, and a rotating parallel dipole line ac-field Hall system with Fourier/lock-in detection for clean Hall signal measurement. We successfully apply this technique to recent world-record-quality perovskite and kesterite films and map the results against varying light intensities, demonstrating unprecedented simultaneous access to the above-mentioned parameters.
Spectrally selective solar absorbers (SSAs), harvesting sunlight into heat, are the key to the concentrated solar thermal systems. Current SSAs designs using photonic crystals, metamaterials, or cermets are either cost-inefficient or have limited app
licability due to complicated nanofabrication methods and poor thermal stability at high temperatures. We present a scalable-manufactured blackbody cavity solar absorber design with nearly ideal properties. The unity solar absorptivity and nearly zero infrared emissivity allow for a stagnation temperature of 880C under 10 suns. The performance surpasses those state-of-the-art SSAs manufactured by nanofabrication methods. This design relies on traditional fabricating methods, such as machining, casting, and polishing. This makes it easy for large-scale industrial applications, and the blackbody cavity feature enables its fast-integration to existing concentrated solar thermal systems.
Dielectric materials, with high tunability at microwave frequencies, are key components in the design of microwave communication systems. Dense Ba0.6Sr0.4TiO3 (BST) ceramics, with different grain sizes, were prepared in order to optimise the dielectr
ic tunability via polar nano cluster effects. Dielectric permittivity and loss measurements were carried at both high and low frequencies and were supported by results from X-ray powder diffraction, scanning and transmission electron microscopies, Raman spectroscopy and piezoresponse force microscopy. The concentration of polar nano clusters, whose sizes are found to be in the range 20 to 50 nm, and the dielectric tunability increase with increasing grain size. A novel method for measurement of the microwave tunability in bulk dielectrics is presented. The highest tunability of 32% is achieved in ceramics with an average grain size of 10 um. The tunability of BST ceramics with applied DC field is demonstrated in a prototype small resonant antenna.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
