اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدV2V Propagation Modeling with Imperfect RSSI Samples
106
0
0.0
(
0
)
نشر من قبل
Silvija Kokalj-Filipovic
تاريخ النشر
2014
مجال البحث
الهندسة المعلوماتية
والبحث باللغة
English
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
We describe three in-field data collection efforts yielding a large database of RSSI values vs. time or distance from vehicles communicating with each other via DSRC. We show several data processing schemes we have devised to develop Vehicle-to-Vehicle (V2V) propagation models from such data. The database is limited in several important ways, not least, the presence of a high noise floor that limits the distance over which good modeling is feasible. Another is the presence of interference from multiple active transmitters. Our methodology makes it possible to obtain, despite these limitations, accurate models of median path loss vs. distance, shadow fading, and fast fading caused by multipath. We aim not to develop a new V2V model, but to show the methods enabling such a model to be obtained from in-field RSSI data.
قيم البحث
اقرأ أيضاً
We propose a method for estimating channel parameters from RSSI measurements and the lost packet count, which can work in the presence of losses due to both interference and signal attenuation below the noise floor. This is especially important in th
e wireless networks, such as vehicular, where propagation model changes with the density of nodes. The method is based on Stochastic Expectation Maximization, where the received data is modeled as a mixture of distributions (no/low interference and strong interference), incomplete (censored) due to packet losses. The PDFs in the mixture are Gamma, according to the commonly accepted model for wireless signal and interference power. This approach leverages the loss count as additional information, hence outperforming maximum likelihood estimation, which does not use this information (ML-), for a small number of received RSSI samples. Hence, it allows inexpensive on-line channel estimation from ad-hoc collected data. The method also outperforms ML- on uncensored data mixtures, as ML- assumes that samples are from a single-mode PDF.
Today, hot embossing and injection molding belong to the established plastic molding processes in microengineering. Based on experimental findings, a variety of microstructures have been replicated so far using the processes. However, with increasing
requirements regarding the embossing surface and the simultaneous decrease of the structure size down into the nanorange, increasing know-how is needed to adapt hot embossing to industrial standards. To reach this objective, a German-Canadian cooperation project has been launched to study hot embossing theoretically by a process simulation and experimentally. The present publication shall report about the first results of the simulation - the modeling and simulation of large area replication based on an eight inch microstructured mold.
We investigate the use of parabolic equation (PE) methods for solving radio-wave propagation in polar ice. PE methods provide an approximate solution to Maxwells equations, in contrast to full-field solutions such as finite-difference-time-domain (FD
TD) methods, yet provide a more complete model of propagation than simple geometric ray-tracing (RT) methods that are the current state of the art for simulating in-ice radio detection of neutrino-induced cascades. PE are more computationally efficient than FDTD methods, and more flexible than RT methods, allowing for the inclusion of diffractive effects, and modeling of propagation in regions that cannot be modeled with geometric methods. We present a new PE approximation suited to the in-ice case. We conclude that current ray-tracing methods may be too simplistic in their treatment of ice properties, and their continued use could overestimate experimental sensitivity for in-ice neutrino detection experiments. We discuss the implications for current in-ice Askaryan-type detectors and for the upcoming Radar Echo Telescope; two families of experiments for which these results are most relevant. We suggest that PE methods be investigated further for in-ice radio applications.
In this paper, we propose a new wrapper feature selection approach with partially labeled training examples where unlabeled observations are pseudo-labeled using the predictions of an initial classifier trained on the labeled training set. The wrappe
r is composed of a genetic algorithm for proposing new feature subsets, and an evaluation measure for scoring the different feature subsets. The selection of feature subsets is done by assigning weights to characteristics and recursively eliminating those that are irrelevant. The selection criterion is based on a new multi-class $mathcal{C}$-bound that explicitly takes into account the mislabeling errors induced by the pseudo-labeling mechanism, using a probabilistic error model. Empirical results on different data sets show the effectiveness of our framework compared to several state-of-the-art semi-supervised feature selection approaches.
In this paper, we propose a machine-learning assisted modeling framework in design-technology co-optimization (DTCO) flow. Neural network (NN) based surrogate model is used as an alternative of compact model of new devices without prior knowledge of
device physics to predict device and circuit electrical characteristics. This modeling framework is demonstrated and verified in FinFET with high predicted accuracy in device and circuit level. Details about the data handling and prediction results are discussed. Moreover, same framework is applied to new mechanism device tunnel FET (TFET) to predict device and circuit characteristics. This work provides new modeling method for DTCO flow.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
