اشترك بالحزمة الذهبية واحصل على وصول غير محدود شمرا أكاديميا
تسجيل مستخدم جديدDevelopment of a Thermal Control System with Mechanically Pumped CO2 Two-Phase Loops for the AMS-02 Tracker on the ISS
399
0
0.0
(
0
)
اسأل ChatGPT حول البحث
ﻻ يوجد ملخص باللغة العربية
To provide a stable thermal environment for the AMS-Tracker, a thermal control system based on mechanically pumped CO2 two-phase loops was developed. It has been operating reliably in space since May 19, 2011. In this article, we summarize the design, construction, tests, and performance of the AMS-Tracker thermal control system (AMS-TTCS).
قيم البحث
اقرأ أيضاً
The electromagnetic calorimeter (ECAL) of the AMS-02 experiment is a 3-dimensional sampling calorimeter, made of lead and scintillating fibers. The detector allows for a high granularity, with 18 samplings in the longitudinal direction, and 72 sampli
ng in the lateral direction. The ECAL primary goal is to measure the energy of cosmic rays up to few TeV, however, thanks to the fine grained structure, it can also provide the separation of positrons from protons, in the GeV to TeV region. A direct measurement of high energy photons with accurate energy and direction determination can also be provided.
The innermost part of the ATLAS experiment will be a pixel detector containing around 1750 individual detector modules. A detector control system (DCS) is required to handle thousands of I/O channels with varying characteristics. The main building bl
ocks of the pixel DCS are the cooling system, the power supplies and the thermal interlock system, responsible for the ultimate safety of the pixel sensors. The ATLAS Embedded Local Monitor Board (ELMB), a multi purpose front end I/O system with a CAN interface, is foreseen for several monitoring and control tasks. The Supervisory, Control And Data Acquisition (SCADA) system will use PVSS, a commercial software product chosen for the CERN LHC experiments. We report on the status of the different building blocks of the ATLAS pixel DCS.
The AMS-02 experiment will be installed on the International Space Station at an altitude of about 400 km in 2010 to measure for three years cosmic rays. The total acceptance including the electromagnetic calorimeter is 0.095 m$^2$sr. This work foc
uses on the anticoincidence counter system (ACC). The ACC is a single layer composed of 16 interlocking scintillator panels that surround the tracker inside the inner bore of the superconducting magnet. The ACC needs to detect particles that enter or exit the tracker through the sides with an efficiency of better than 99.99 %. This allows to reject particles that have not passed through all the subdetectors and may confuse the charge and momentum measurements which is important for an improvement of the antinuclei-measurements. In 2007/2008 all subdetectors were integrated into the AMS-02 experiment and atmospheric muons were collected. These data were used to determine the ACC detection efficiency.
Fine pixel CCD (FPCCD) is one of the candidate sensor technologies for the vertex detector used for experiments at the International Linear Collider (ILC). FPCCD vertex detector is supposed to be cooled down to -40 degree for improvement of radiation
immunity. For this purpose, a two-phase CO2 cooling system using a gas compressor for CO2 circulation is being developed at KEK. The status of this R&D is presented in this article.
The Belle II experiment at the SuperKEKB e+e- collider in KEK, Japan does start physics data-taking from early of 2018 with primary physics goal that is to probe the New Physics effect using heavy quark and lepton weak decays. During trigger and DAQ
operation upon beam collision, it is important that Belle II detector (Fig. 1) status have to be monitored in a process of data-taking against an unexpected situation. Slow control system, built in the Control System Studio (CSS) which is a GUI window design tool based on Eclipse, is one of monitoring and controlling systems in Belle II operation. Database and archiver servers are connected to slow control system. Experimental parameters are downloaded to Belle II main database server which is based on PostgreSQL. Real-time results are stored in archiver server which is based on EPICS (The Experimental Physics and Industrial Control System) archiver appliances and tomcat which is open-source java servlet container. In this study, we report the development of slow control system for the Belle II electromagnetic calorimeter (ECL) trigger system.
سجل دخول لتتمكن من نشر تعليقات
التعليقات
جاري جلب التعليقات
سجل دخول لتتمكن من متابعة معايير البحث التي قمت باختيارها
